version 1.2, 2003/04/05 22:24:43
|
version 1.3, 2003/04/14 14:30:39
|
|
|
\author{Dave Gaskell} | \author{Dave Gaskell} |
\category{general} % Subject area of this document | \category{general} % Subject area of this document |
%\maintainer{Name of person maintaining document} % Optional | %\maintainer{Name of person maintaining document} % Optional |
\date{April 3, 2003} |
\date{April 14, 2003} |
| |
\begin{document} | \begin{document} |
| |
|
|
\begin{itemize} | \begin{itemize} |
\item{Connect to terminal server 7, port 3, i.e., | \item{Connect to terminal server 7, port 3, i.e., |
\texttt{telnet hctsv7 2003}.} | \texttt{telnet hctsv7 2003}.} |
\item{Hit return to get a \texttt{B->} prompt.} |
\item{Hit return to get a \texttt{B->} prompt.\\ |
|
NOTE: Occasionally, just hitting return does not work. If you hit return a |
|
few times and do not get a prompt, try typing \texttt{$\backslash$B} |
|
(the old procedure). This will hopefully get you a prompt.} |
\item{Type \texttt{EN}, to enable the motor.} | \item{Type \texttt{EN}, to enable the motor.} |
\item{Type \texttt{RUN 10} and follow the instructions.} | \item{Type \texttt{RUN 10} and follow the instructions.} |
\item{After the slit is in place, disable the motor by typing ``1''.} | \item{After the slit is in place, disable the motor by typing ``1''.} |
|
|
\end{center} | \end{center} |
\end{table} | \end{table} |
| |
|
\section{Troubleshooting} |
|
|
|
\begin{itemize} |
|
|
|
\item{\emph{When I try to log in to the HMS slit controller, I get the} |
|
\texttt{PortServer~8} \emph{text, but when I hit return, nothing happens.}\\ |
|
Try hitting return a couple times and wait a few seconds (like maybe 5-10). |
|
If still nothing happens, try typing \texttt{$\backslash$B} (the old |
|
procedure).} |
|
|
|
\item{\emph{I can log in, and I get a prompt, but when I try} \texttt{run 10} |
|
\emph{I get some weird error message about not being at the right level |
|
(error 63).}\\ |
|
In this case, it is likely that the controller has been left in monitor--mode. |
|
If your prompt has two lines before the arrow (i.e. \texttt{B=>}) ,this is |
|
likely the case. Try hitting \texttt{escape} to get out of monitor mode and |
|
start over from \texttt{EN}.} |
|
|
|
\end{itemize} |
| |
| |
\end{document} | \end{document} |
|
|
% | % |
% Revision history: | % Revision history: |
% $Log$ | % $Log$ |
|
% Revision 1.3 2003/04/14 14:30:39 saw |
|
% (gaskelld) Add a troubleshooting section |
|
% |
% Revision 1.2 2003/04/05 22:24:43 saw | % Revision 1.2 2003/04/05 22:24:43 saw |
% (gaskelld) Added info on how to check collimator positions and table of | % (gaskelld) Added info on how to check collimator positions and table of |
% nominal positions | % nominal positions |