Shift crew procedures

Compton Procedures Sheet (short version for shift workers)

General Compton running

1. At least once every hour restart a new CODA run. CODA should be open on one of the desktops of ccomptl1.
2. At least once every hour check the status of the HV. If a trip occurred, see below.
3. Check whether the laser is still flipping (EPICS channel cComptCavityPower).

   This should be obvious from the camera as well. If not flipping, call an expert. This EPICS PV should be visible on the desktop of Striptools on ccomptl1.

4. Monitor the background scintillator rates. cComptScintRateNorm should stay below 200 Hz/uA. If the rates climb above 200 Hz/uA, please call a Compton expert. If the rates climb above 300 Hz/uA, turn off the photon detector HV and call a Compton expert.

   Special note: Nov 26 we have seen the backgrounds climb to 1-2 kHz/uA for several minutes, then improve on their own. These elevated rates should be ok for the electron detector, but it would be good to turn OFF the photon detector until the backgrounds improve. If the backgrounds remain high for more than a few minutes with no sign of improvement, call a Compton expert to see if we should back out of the chicane.

5. Electron detector: the nominal position for the electron detector is "8.7890" - the motion control screen can be seen on the 3rd desktop of the Compton computer. DO NOT move the electron detector if you have not done this before in guidance of an expert. Call a Compton expert. Beam should always be off before moving the e-detector
6. For any reason if MCC has to tune beam to the hall, the electron detector needs to be put to Garage

1. notice there's a difference between sending tune beam to the Hall as against tuning the beam to the Hall.

After a photon detector HV trip

1. Check that the normalized rate on the background scintillator (EPICS channel cComptScintRateNorm, or manually normalize hcrate14) is still below 150 Hz/uA (200 Hz/uA is tolerable, <150 Hz/uA is "ok", <100 Hz/uA is "good.").

   This EPICS PV should be visible on the desktop of Striptools on ccomptl1. If not, call an expert.
   

2. Wait 5 minutes after the trip and turn on the HV on the photon detector to 1700 V (channel ComptPhoton).
   

   The HV controls should be open on one of the ccomptl1 desktops. If not log on to cdaql4 as cvxwrks and cd to $EPSHV/tk then run /HV_compton.tcl and turn on PhotonDet_6.
   

3. If the photon detector HV trips again within 15 minutes, call an expert.
   

If you notice e-detector motion GUI hung-up

1. If we do not need to move the e-detector, then make an hclog post with email to (narayan, gaskelld). It will be fixed soon enough
2. If you need to move the e-detector right away(either to beam-position or to Garage), call the Compton expert on call.

Moving the electron-detector

For more clear instructions on when to move, why to move and how to move, one can check the [detailed instructions]

'BEAM' position from 'Garage' position

1. Make sure beam is off and 'Compton e-detector motion FSD' is masked
2. Before moving the e-detector out of Garage (motion GUI is on 3rd Desktop) press the 'Read' button on the top-right region of the GUI
3. On doing the above, if you see a 'COMM' error,
   1. DO NOT make any further effort to move the e-detector.
   2. Call the expert on call
   3. If the detector was at Garage and you did not attempt to move it, then the location of the detector is unchanged from Garage hence you may proceed with Parity data, while the expert calls back and fixes the communication problem.
4. Select 'HOME' from the first drop-down menu
5. If you see a COMM error now
   1. Please be aware that beam cannot be taken without either fixing the problem or due authorization from Dave Gaskell.
   2. Contact on-call compton expert to fix the communication problem of the motion GUI.
   3. Call MCC and inform that we are not sure of the exact location of the e-detector and hence we cannot take beam unless it is resolved
6. If the detector has reached 'HOME' and you see the 'HOME' button turn green
   1. Select 'Pos-2' from the first drop-down menu
   2. Wait for the 'moving' button (yellow during active motion) to get uncolored
   3. Check on the top left position read-back to be X=8.7890
7. The motion is done and you would see the Hall C Wall screen show 'BEAM' against e-detector position.

'Garage' position from 'BEAM' position

1. Make sure beam is already off and the 'Compton e-detector motion FSD' is masked
2. Select 'Garage' from the first drop-down menu
3. Wait for the 'moving' button (yellow during active motion) to get uncolored
4. Check to see the top left position read-back to be X=-9.5xxx
5. The motion done and you would see the Hall C Wall screen show 'Garage' against e-detector position

Starting CODA from Scratch

We have a Trigger supervisor ROC, ROC1 and ROC2 in the Compton DAQ setup. We also use CODA 2.6.1 with many things in common with Qweak. The regular shift worker may need to look at more detailed instructions. Following are the salient features of our CODA setup.

1. run configuration is 'standard'
2. session is 'compton_ccomptl1'

Compton Experts

Call or page in the order below. Wait a few minutes before moving on to the next name on the list.

• Dave Gaskell, pager gaskelld-page@jlab.org, cell 719-5482
• Mark Dalton (laser)
• Don Jones (photon detector and laser) cell 768-1148
• Wouter Deconinck, pager 238-4235, cell 927-2413
• Amrendra Narayan (electron detector and DAQ) cell 952-6126
• Juan Carlos Cornejo (DAQ)