Difference between revisions of "RC Meeting, Tuesday, Dec 14, 2021"
(→Current Run Plan) |
(→Future plans) |
||
Line 44: | Line 44: | ||
= Future plans = | = Future plans = | ||
* Continue production data at 70 uA on LH2 (SHMS right) - expect to switch to SHMS center tomorrow on DAY shift | * Continue production data at 70 uA on LH2 (SHMS right) - expect to switch to SHMS center tomorrow on DAY shift | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
= Current Run Plan = | = Current Run Plan = |
Revision as of 09:26, 14 December 2021
Contents
RC Meeting Information
Have RC meeting today
RC Daily Meetings are at 10 AM, remote
- Bluejeans remote connection information:
To join the Meeting: https://bluejeans.com/861439920 To join via Room System: Video Conferencing System: bjn.vc -or-199.48.152.152 Meeting ID : 861439920 To join via phone : 1) Dial: +1.408.740.7256 (US (San Jose)) +1.888.240.2560 (US Toll Free)) +1.408.317.9253 (US (Primary, San Jose)) (see all numbers - http://bluejeans.com/numbers) 2) Enter Conference ID : 861439920
Useful Links
- Fall 2021 Shift Schedule
- PionLT Physics Status
- PionLT Runplans
- Hall-C Controls
- Hall-C Logbook
- MCC White Board
- OPS 7:45 RC meeting bluejeans link, weekends usually 9am.
- OPS daily 8:00 meeting and Wed 1:30 bluejeans link
- Note: 7:45, 8 am and 1:30 scheduling meetings will switch to Zoom starting with 1:30 scheduling meeting on Wednesday, December 15
- OPS 7:45 RC meeting Zoom link TBD
- OPS daily 8:00 meeting and Wed 1:30 new Zoom link
Current Status
Current RC: Dave Gaskell
On Owl shift, completed deuterium data taking for LD2, pi+ Q2 =6.00 GeV2, W=2.40 GeV, x=0.55, low epsilon, right. Total pions = 17,797 (out of 23,000 from original projections): https://logbooks.jlab.org/entry/3962573
Switched to LH2 at ~ 4 am. pi+ rate about the same: ~ 700 pions/hour (1493 pions after 1st 2 runs).
Future plans
- Continue production data at 70 uA on LH2 (SHMS right) - expect to switch to SHMS center tomorrow on DAY shift
Current Run Plan
We are currently on (Ebeam=8.0 GeV) Q2=6.00, W=2.40, x=0.55, low ε data taking – PART TWO [See run plan]
- Target: LH2
Q2=6.00 GeV2, W=2.40 GeV, x=0.55, low epsilon, HMS angle=34.58deg, HMS momentum = -2.139 GeV/c SHMS angle= 9.12deg (right), SHMS momentum= 5.512 GeV/c
Notices in Effect for Shift Crew
- The Raster Coil pair Ax and Ay are off. Raster needs to be at 4x4.
- With LHe alarms it is good to check the cameras for plumes. If no plume and it is below the LO alarm and above LOLO then monitor with a plot and halog the problem.
- With LNitrogen alarms are not that critical. Just need to start monitoring the problem with plot and Halog.
Current Issues
- There is a rotation issue that has come up if moving HMS between 19 to 25 degrees. It usually gets stuck around this range, please be wary of this issue. We will likely skip settings in this range if this drive controller error cannot be solved. For singles it will not be a big deal to skip settings for HMS at those angles. We need a longer access to address this issue (cannot be done on Tuesday 12/14)
- SHMS cannot be rotated to angles > 30 degrees - the proximity switch has either moved or was accidentally set in the wrong place. Not an issue for now - will be addressed before we restart in January,
- The Raster Coil pair Ax and Ay are off
- Diffuser limit at 46uA (Note: is this still valid?)
Crew Chiefs,
We have permission to raise the Hall C diffuser raster limit to allow running >46uA to Hall C. This limit is normally imposed when one of the two rasters is not operative. Since the hall was able to double the running raster current to get the same size raster on the target as having both rasters, Keith is allowing us to raise the limit.
To get to the setting, open the Hall C diffuser interlocks screen. Go to the bottom right corner and open the Expert screen. Just below and to the right of the FSD bits, raise the "Raster 1 OK Limit" to slightly above the highest current the hall wants to run at. Do not change the Raster 2 limit. Make a log entry with screen shots. Make an ABIL entry, System MPS and an expected removal date of 3 Jan. 2022.
Paul
Planned Accesses to the Hall
- OPS Beam injector test tomorrow Tuesday (12/14) scheduled 9 AM- 1 PM (no beam during this time)
- Radcon (David Hamlette) confirmed they can allow controlled access 9-1 pm tomorrow during beam injector test to allow maintenance work on SHMS and HMS. Work by Walter Kellner and Steve Lassiter to start around 10 AM (after radon survey is complete). Work should take about 2-3 hours. Not long enough of an access to address HMS rotation issues.
- Maintenance to pump down HMS transfer line.
- Need to clean the SHMS encoder wheel.
- Radcon (David Hamlette) confirmed they can allow controlled access 9-1 pm tomorrow during beam injector test to allow maintenance work on SHMS and HMS. Work by Walter Kellner and Steve Lassiter to start around 10 AM (after radon survey is complete). Work should take about 2-3 hours. Not long enough of an access to address HMS rotation issues.
Planned Accelerator Configuration Changes
- none
Special Requests
- none