Difference between revisions of "RC Meeting and Run Plan, Fri, January 17th 2020"
From HallCWiki
(Created page with "= RC Meeting Information = <b> RC Daily Meetings are at 4:15 PM, 2nd floor Counting House Meeting Room </b> * Bluejeans remote connection information: To join the Meeting:...") |
(→General updates) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 25: | Line 25: | ||
=General updates= | =General updates= | ||
| − | * | + | *Over Thursday Swing and Owl, beam off or low current. |
| − | * | + | * Friday morning MCC did RF recovery for 1 hour and worked on reduce BLM trips at 9S. |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
= Current Run Plan = | = Current Run Plan = | ||
| − | * Take NMR every | + | * Take NMR every 2 hours |
| − | * Always take | + | * Always take 120Hz of EDTM |
| − | == | + | == Friday Swing/Owl == |
*A3) production: [https://hallcweb.jlab.org/wiki/index.php/5-pass_production_for_A1n#Large_Angle_.2830-degree.29_Polarized_3He_Asymmetries_High_Momentum_Setting_.28Kine_4.2CB.29 Run Plan] | *A3) production: [https://hallcweb.jlab.org/wiki/index.php/5-pass_production_for_A1n#Large_Angle_.2830-degree.29_Polarized_3He_Asymmetries_High_Momentum_Setting_.28Kine_4.2CB.29 Run Plan] | ||
| − | == | + | == Saturday Day == |
*Moller measurement will start around 8am. | *Moller measurement will start around 8am. | ||
**Start with Moller setup and measurement at present Wien angle (last about 4 hours). | **Start with Moller setup and measurement at present Wien angle (last about 4 hours). | ||
| Line 48: | Line 43: | ||
* Keep target expert schedule filled out on whiteboard | * Keep target expert schedule filled out on whiteboard | ||
* Andy Kenyon has parts ready for the nitrogen for the cooling jets.= Ongoing Work in the Hall | * Andy Kenyon has parts ready for the nitrogen for the cooling jets.= Ongoing Work in the Hall | ||
| − | + | ||
= Notices in Effect for Shift Crew = | = Notices in Effect for Shift Crew = | ||
Latest revision as of 17:18, 17 January 2020
Contents
RC Meeting Information
RC Daily Meetings are at 4:15 PM, 2nd floor Counting House Meeting Room
- Bluejeans remote connection information:
To join the Meeting: https://bluejeans.com/861439920 To join via Room System: Video Conferencing System: bjn.vc -or-199.48.152.152 Meeting ID : 861439920 To join via phone : 1) Dial: +1.408.740.7256 (US (San Jose)) +1.888.240.2560 (US Toll Free)) +1.408.317.9253 (US (Primary, San Jose)) (see all numbers - http://bluejeans.com/numbers) 2) Enter Conference ID : 861439920
Useful Links
General updates
- Over Thursday Swing and Owl, beam off or low current.
- Friday morning MCC did RF recovery for 1 hour and worked on reduce BLM trips at 9S.
Current Run Plan
- Take NMR every 2 hours
- Always take 120Hz of EDTM
Friday Swing/Owl
- A3) production: Run Plan
Saturday Day
- Moller measurement will start around 8am.
- Start with Moller setup and measurement at present Wien angle (last about 4 hours).
Special Requests
- Keep target expert schedule filled out on whiteboard
- Andy Kenyon has parts ready for the nitrogen for the cooling jets.= Ongoing Work in the Hall
Notices in Effect for Shift Crew
- Policy for CANS-related hall status change: Make a logbook entry when the hall goes in, or comes out of laser-controlled access.
- Magnet policies
- HMS Q1 must be ramped down in 50A steps in all cases
- Do not ramp HMS Q2 to zero, only go to 10A and then switch off power.
- Inform the RC of any access that the Target Team requires. The RC will coordinate with RadCon to make everything run smoothly.
- The operators have been somewhat careful with our beam orbit locks. Please make sure that the orbit locks are enabled and the beam does not drift from its nominal position.
- Ramp rate lock instructions are here and added to checklist[1]
- Temporary Laser instructions can be found here [2]
