Difference between revisions of "Resetting Magnet Interlocks"
From HallCWiki
(6 intermediate revisions by 3 users not shown) | |||
Line 16: | Line 16: | ||
#Reset the interlock(s) and continue. | #Reset the interlock(s) and continue. | ||
*Most interlocks are reset simply by pressing the associated "RESET" button on the screen. | *Most interlocks are reset simply by pressing the associated "RESET" button on the screen. | ||
− | *If the | + | ** Joe says: If you have trouble resetting the Slow Discharge, trip the Fast Discharge, and then start again. |
+ | *'''Expert Only:''' If the power supply has just been turned on, for example after a power cycle, follow these instructions: (https://hallcweb.jlab.org/wiki/index.php/File:HMS_Quad_PSU_reset_2021.pptx ) | ||
*If the PSU remains off even after clearing interlocks and pressing "Power On", you may need to press "Power Off" then "Power On" again. | *If the PSU remains off even after clearing interlocks and pressing "Power On", you may need to press "Power Off" then "Power On" again. | ||
*It is most likely that after you reset the interlocks in any of the Magnets, the "set current" value goes to zero, please check the "set current" value in the Magnet GUI .Follow the regular procedure to set the proper current based on your run plan. | *It is most likely that after you reset the interlocks in any of the Magnets, the "set current" value goes to zero, please check the "set current" value in the Magnet GUI .Follow the regular procedure to set the proper current based on your run plan. | ||
− | |||
[[File:MagnetInterlockScreen.png|thumb|left]] | [[File:MagnetInterlockScreen.png|thumb|left]] | ||
[[File:MagnetPSUScreen.png|thumb|left]] | [[File:MagnetPSUScreen.png|thumb|left]] |
Latest revision as of 19:17, 27 November 2021
The spectrometer magnets are protected against faults by numerous interlocks built into the controls system. Users are permitted to attempt to RESET magnet interlocks and restore the magnet settings so that experiment operations can continue.
- Each magnet power supply screen (PSU) displays the status of a number of interlocks.
- Each magnet has its own INTERLOCKS screen.
- These screens are reached through the strip menus at the top of the magnets controls screen. Examples are included below.
Look over these screens and assure yourself that there is no actual apparent problem that should prevent the magnet from operating. For example:
- Is a cryogenic liquid level actually low?
- Is there a general power failure in the hall?
- Is there a plume of smoke visible on a hall TV screen?
- Have you already tried repeatedly to reset an interlock but it keeps coming back?
- In this case it is time to contact one of the magnet system experts.
If things appear to be OK,
- Capture an image of both the interlocks screen and the magnet power supply screen and post them in the logbook.
- Reset the interlock(s) and continue.
- Most interlocks are reset simply by pressing the associated "RESET" button on the screen.
- Joe says: If you have trouble resetting the Slow Discharge, trip the Fast Discharge, and then start again.
- Expert Only: If the power supply has just been turned on, for example after a power cycle, follow these instructions: (https://hallcweb.jlab.org/wiki/index.php/File:HMS_Quad_PSU_reset_2021.pptx )
- If the PSU remains off even after clearing interlocks and pressing "Power On", you may need to press "Power Off" then "Power On" again.
- It is most likely that after you reset the interlocks in any of the Magnets, the "set current" value goes to zero, please check the "set current" value in the Magnet GUI .Follow the regular procedure to set the proper current based on your run plan.