Difference between revisions of "Bull's Eye Scan"
From HallCWiki
Jump to navigationJump to search| Line 8: | Line 8: | ||
NOTE: The positions above can be experiment specific. Confirm with RC. | NOTE: The positions above can be experiment specific. Confirm with RC. | ||
| − | + | '''Procedure''' | |
'''Starting Settings''' | '''Starting Settings''' | ||
Beam: 5uA CW, Raster OFF | Beam: 5uA CW, Raster OFF | ||
| Line 15: | Line 15: | ||
Have a stripchart of the 3HO4A, 3HO4B, and 3HO4C BPMs visible. [Run '''go_stripchart''', if needed.] | Have a stripchart of the 3HO4A, 3HO4B, and 3HO4C BPMs visible. [Run '''go_stripchart''', if needed.] | ||
| − | + | '''Start an HCLOG entry titled 'BPM calibration' and record the following for each of the 5 (x, y) points above''' | |
* Requested Beam Position | * Requested Beam Position | ||
* HMS/SHMS Run numbers | * HMS/SHMS Run numbers | ||
* Harp Scan log entries | * Harp Scan log entries | ||
| − | + | '''For each of the 5 points identified above, do the following''' | |
* We want all BPMs to have (roughly) the same values for each point (so the beam is roughly parallel to the beamline). '''Tolerances of +-0.3 or so on the requested numbers are fine'''. | * We want all BPMs to have (roughly) the same values for each point (so the beam is roughly parallel to the beamline). '''Tolerances of +-0.3 or so on the requested numbers are fine'''. | ||
* Be sure the BPMs and beam are stable, start a CODA '''in each arm''' for a few minutes, then call MCC and request that they run and log a harp scan for both 3H07A and 3H07B to the HCLOG. | * Be sure the BPMs and beam are stable, start a CODA '''in each arm''' for a few minutes, then call MCC and request that they run and log a harp scan for both 3H07A and 3H07B to the HCLOG. | ||
| Line 26: | Line 26: | ||
Just leave the CODA run going during the scans. | Just leave the CODA run going during the scans. | ||
| − | + | '''Submit your HCLOG summary table''' | |
* Make sure your table is complete | * Make sure your table is complete | ||
* Add a screen snapshot of the BPM stripchart | * Add a screen snapshot of the BPM stripchart | ||
Revision as of 16:13, 5 December 2019
Bull's Eye Scan: BPM vs Harp scan Calibration
Goals We want to be able to correlate the BPM ADC data with the "absolute" positions given by the surveyed Harp scanners for these nominal BPM positions: (0, 0), (+3,+3), (+3,-3), (-3,+3), (-3,-3)
NOTE: The positions above can be experiment specific. Confirm with RC.
Procedure
Starting Settings Beam: 5uA CW, Raster OFF Beam Position: (0, 0) Target: Carbon or 'No Target' Have a stripchart of the 3HO4A, 3HO4B, and 3HO4C BPMs visible. [Run go_stripchart, if needed.]
Start an HCLOG entry titled 'BPM calibration' and record the following for each of the 5 (x, y) points above
- Requested Beam Position
- HMS/SHMS Run numbers
- Harp Scan log entries
For each of the 5 points identified above, do the following
- We want all BPMs to have (roughly) the same values for each point (so the beam is roughly parallel to the beamline). Tolerances of +-0.3 or so on the requested numbers are fine.
- Be sure the BPMs and beam are stable, start a CODA in each arm for a few minutes, then call MCC and request that they run and log a harp scan for both 3H07A and 3H07B to the HCLOG.
Just leave the CODA run going during the scans.
Submit your HCLOG summary table
- Make sure your table is complete
- Add a screen snapshot of the BPM stripchart
