Difference between revisions of "Pol He-3 Target Screen Setup"
From HallCWiki
Jump to navigationJump to search| Line 9: | Line 9: | ||
== Setup target laser controls on '''POLTARCC''' == | == Setup target laser controls on '''POLTARCC''' == | ||
| + | |||
| + | === Connect to the Laser computer (polhe1) === | ||
* Go to POLTARCC (single monitor linux host to the right in the corner of the TO station) | * Go to POLTARCC (single monitor linux host to the right in the corner of the TO station) | ||
| − | * Open a terminal on an empty workspace | + | ** Open a terminal on an empty workspace |
| − | * Run '''go_lasers' | + | ** Run '''go_lasers' |
| − | + | NOTE: This opens a VNC client connecting to the polhe1 Windows computer in the Laser room. | |
| − | * Double | + | It will go full screen when it starts. Hit the '''F8''' key to exit the VNC screen if necessary. |
| − | + | ||
| + | === Run the Laser Control and EPICS binder software === | ||
| + | [[Image:polhe3-lasers-step1.jpg|thumb]] | ||
| + | * Double-click on the '''Raytum D-Light Laser Controller, Multiple Station''' icon in the top-middle of the screen. | ||
| + | <br clear=all> | ||
| + | |||
| + | [[Image:polhe3-lasers-step2.jpg|thumb]] | ||
| + | * On the Sidebar that appears Double-click on the D-Light Laser Controller, Multiple Station.vi line (highlighted here) | ||
| + | <br clear=all> | ||
| + | |||
| + | [[Image:polhe3-lasers-step3.jpg|thumb]] | ||
| + | * Click on the white arrow near the top of the window that pops up to run the | ||
| + | program. The system will search for the lasers -- be patient, it can take | ||
| + | 30-60 seconds until the desired lasers show 'OK'. Click '''Accept''' and the | ||
| + | main laser panel will appear with all accessible lasers. | ||
| + | <br clear=all> | ||
| + | |||
| + | [[Image:polhe3-lasers-step4.jpg|thumb]] | ||
| + | * On the same Sidebar, expand ''EPICS.lvlib'' and double-click on '''Adapter.vi'''. | ||
| + | ** Click on the white 'run' arrow at the top of the window. This binds the LabVIEW variables to an EPICS IOC for monitoring and logging. | ||
| + | <br clear=all> | ||
| + | |||
| + | [[Image:polhe3-lasers-step5.jpg|thumb]] | ||
| + | * '''Minimize''' (do ''not'' close) all windows except for the '''D-Light Laser Controller''' window. | ||
| + | ** Your screen should look similar to the snapshot. | ||
| + | <br clear=all> | ||
== Setup target Polarimetry controls on '''POLHE4''' == | == Setup target Polarimetry controls on '''POLHE4''' == | ||
Revision as of 23:38, 14 December 2019
Pol He-3 Target Screen Setup
Setup target ladder, stripcharts on HCDESK4
To setup non-LabVIEW screens (stripcharts, target ladder, etc)
- Go to HCDESK4 (dual monitor linux host to the right of the TO station) and open a terminal on an empty workspace
- Run go_target
- Arrange the screens as shown in the snapshot
Setup target laser controls on POLTARCC
Connect to the Laser computer (polhe1)
- Go to POLTARCC (single monitor linux host to the right in the corner of the TO station)
- Open a terminal on an empty workspace
- Run go_lasers'
NOTE: This opens a VNC client connecting to the polhe1 Windows computer in the Laser room. It will go full screen when it starts. Hit the F8 key to exit the VNC screen if necessary.
Run the Laser Control and EPICS binder software
- Double-click on the Raytum D-Light Laser Controller, Multiple Station icon in the top-middle of the screen.
- On the Sidebar that appears Double-click on the D-Light Laser Controller, Multiple Station.vi line (highlighted here)
- Click on the white arrow near the top of the window that pops up to run the
program. The system will search for the lasers -- be patient, it can take
30-60 seconds until the desired lasers show 'OK'. Click Accept and the
main laser panel will appear with all accessible lasers.
- On the same Sidebar, expand EPICS.lvlib and double-click on Adapter.vi.
- Click on the white 'run' arrow at the top of the window. This binds the LabVIEW variables to an EPICS IOC for monitoring and logging.
- Minimize (do not close) all windows except for the D-Light Laser Controller window.
- Your screen should look similar to the snapshot.
Setup target Polarimetry controls on POLHE4
FIXME: ADD INSTRUCTIONS AND SCREEN SNAPSHOTS HERE WHEN ALL IS WORKING Just placeholders below.
How to do EPR_FM sweep
How to do EPR-AFP
How to take pNMR measurement
How to take NMR measurement
LabVIEW software notes
Need to add what folder these can be found in.
EPR software
- EPR-RM sweep: EPR_FM_PIBOX_0_A1n_D2n.vi
- EPR-AFP: EPR_AFP_Modified_v3_A1n_D2n.vi
EPICS bindings
- Laser bindings (polhe1)
- Polarimetry bindings (polhe4)
