Jefferson Lab Hall C Logbook for July 10 - runstarts omitted
Main INDEX
Saturday
196496 07/31/10 23:49 Leckey Swing Shift Summary
196495 07/31/10 23:25 pking/kaisen Added "beam off" pedestals for main detectors and lumis
196492 07/31/10 22:51 saw Exit window temperature
196491 07/31/10 22:32 Armstrong Exit Window Temp
196488 07/31/10 22:10 leacock changed back to 240Hz provided by MCC
196485 07/31/10 22:03 leacock now at 1000Hz fake mps
196480 07/31/10 21:45 leacock lumi ADCs were not in the datastream from run 959 - 969
196479 07/31/10 21:21 Armstrong updated run plan
196478 07/31/10 21:14 Leckey Beam back off
196477 07/31/10 21:04 leacock lumi HV off
196476 07/31/10 20:55 Leckey Tune Beam in Hall
196473 07/31/10 20:21 Arshak GEM noise still not fixed.
196472 07/31/10 20:21 Arshak GEM noise still not fixed.
196471 07/31/10 20:13 benesch Beam: 3H07 harp traces
196470 07/31/10 20:06 benesch elog entries relating to vacuum events
196459 07/31/10 18:38 Leckey Hall survey to replace Lumi
196458 07/31/10 18:33 Armstrong Waiting on beam
196451 07/31/10 18:25 Leckey Down for 1hr
196450 07/31/10 18:14 Leckey BCM1 Setting 3 to 5
196448 07/31/10 18:11 pking/kaisen Analysis: Added "beam off" pedestals for hall C beamline devices
196446 07/31/10 17:12 Armstrong CW beam in Hall
196444 07/31/10 17:00 Pitt Day shift summary
196442 07/31/10 16:58 pking Reset the 31MHz clock
196441 07/31/10 16:46 cdaq Beam Time Accounting
196440 07/31/10 15:27 Pitt High voltages during run 957
196439 07/31/10 15:25 Pitt Dump window water flow
196438 07/31/10 15:20 Pitt Status
196437 07/31/10 15:14 Pitt Tune beam to hall
196434 07/31/10 13:39 Pitt USLUMI status during run 956
196433 07/31/10 13:37 pqwang MD4+ and MD5- 'drak' current measurement
196432 07/31/10 13:25 Pitt High voltages off except MD5- and MD4+
196429 07/31/10 12:41 Pitt MD CM and USLUMI CM high voltages on
196428 07/31/10 12:33 Pitt Accelerator vacuum expert arrives
196427 07/31/10 12:33 Pitt Accelerator vacuum expert arrives
196424 07/31/10 11:23 pking Changed the TS trigger input assignments
196423 07/31/10 08:26 Pitt Status
196422 07/31/10 00:27 leacock all HV off
196421 07/31/10 00:23 leacock lumi status
196420 07/31/10 00:02 smith,covrig Target: Target plans for the next little while
Friday
196419 07/30/10 23:40 smith,covrig Target: Parked target for night.
196418 07/30/10 23:37 R. Subedi Status update (no Owl shift tonight)
196417 07/30/10 23:32 smith,covrig Target: Went home on target. Target is out.
196416 07/30/10 23:31 smith,covrig Target: removed transits, ladders, tripods
196415 07/30/10 23:20 smithg Target: Aborted cooldown
196393 07/30/10 18:59 benesch Target: another link to elog on leak
196385 07/30/10 18:33 benesch Target: Target leak started at 1805
196380 07/30/10 17:58 saw Qtor on at 10 Amps (shift crews please read)
196379 07/30/10 17:52 smithg Target: Plan for tonight & tomorrow.
196378 07/30/10 17:42 vulcan sight
196365 07/30/10 16:00 Fenker Oh yeah: I fixed the gas leak
196359 07/30/10 15:42 Fenker Log all Alarms, please
196354 07/30/10 15:26 pking GUI TGT JT control might work
196351 07/30/10 14:57 gaskell Shutting Moller JTs - no cooldown today
196350 07/30/10 14:26 benesch Beam: hall C optics measurement results
196349 07/30/10 14:25 smithg Target: 4K cooldown status
196340 07/30/10 13:42 leacock dslumi status -- evens have been isolated from the noise
196337 07/30/10 12:59 Pitt Region 2 chambers parked
196336 07/30/10 12:33 Armstrong Region 3 chambers parked
196335 07/30/10 12:28 smithg Target: Started (4K) cooldown
196334 07/30/10 12:25 jhoskins Hall C rotator notes
196333 07/30/10 12:15 pqwang MD current mode HV and offset rechecked
196329 07/30/10 11:51 smithg Target: preparing to start cooldown
196325 07/30/10 08:41 smithg Target: no remote control of JTs
196324 07/30/10 08:35 gaskell Compton photon detector installed
196323 07/30/10 00:09 silviu Target: horizontal table switches are out
Thursday
196322 07/29/10 21:53 pking Modifed cdaql6 login scripts and CODA scripts
196301 07/29/10 19:40 leacock bad run
196285 07/29/10 17:28 leacock ethane alarms when fridge in gas shed is opened
196283 07/29/10 17:16 pqwang Turned off HV for MD4+ and MD5-
196282 07/29/10 17:09 Arshak GEM (Region-1)Hut entrance is closed.
196281 07/29/10 17:01 pking Added EPICS environment set up to cdaq@cdaql6 boot script
196274 07/29/10 16:37 jhoskins Rotator Position
196272 07/29/10 16:25 Don Jones Compton: ADC problem resolved.
196271 07/29/10 16:21 kenyon Surgetank vacuum
196266 07/29/10 15:57 smithg Target: no cooldown today
196257 07/29/10 12:27 Armstrong VDC protective plates are off
196250 07/29/10 11:49 pqwang MD current mode HV turned on
196249 07/29/10 11:39 leacock dslumi8 base disconnected from PMT
196246 07/29/10 11:33 silviu Target: pressures and vacuum
196244 07/29/10 11:30 leacock bad run
196242 07/29/10 11:29 Armstrong HVAC in Counting House C
196238 07/29/10 11:03 leacock all HV disconnected from lumi HV power crate in hall
196214 07/29/10 06:58 leacock hard reboot of ROC2 and CODA restart worked
196209 07/29/10 06:36 leacock both of the lumi ADCs and both of the MD ADCs are dropping events
Wednesday
196207 07/28/10 22:42 smithg, covr Target: helium pump & purge of tgt loop & gas panel completed
196206 07/28/10 21:56 pking Late entry: Helicity events now accepted as "program 1" events.
196202 07/28/10 17:01 smithg Target: starting helium pump & purge of gas panel and target loop
196201 07/28/10 16:51 jhlee one reserved F1TDC crate in the counting house
196190 07/28/10 15:02 kenyon Beamline turbo studs
196185 07/28/10 14:27 Armstrong Sanity check on Trigger Scintillator orientation vs. VDC
196175 07/28/10 13:22 smacewan MD run 843 LED cable map and Reference signals
196174 07/28/10 12:59 Jie Pan Scanner rate map with an "OR" self-trigger, tested with event mode electronics
196171 07/28/10 12:37 pking DAQ modification for trigger supervisor
196170 07/28/10 11:51 pqwang MD current mode HV turned off
196163 07/28/10 10:46 Jie Pan Scanner rate map with an "OR" self-trigger
196162 07/28/10 10:45 Jie Pan Scanner rate map with an "OR" self-trigger
Tuesday
196141 07/27/10 18:47 benesch acattering chamber vacuum jumped a factor of two at 1802
196140 07/27/10 18:44 smacewan Main detector preamp offset with HV on
196139 07/27/10 18:30 Kargiantoula Beam: RHWP scan results for 1i04
196138 07/27/10 18:28 Kargiantoula Beam: RHWP scan results for 1i02
196135 07/27/10 18:00 leacock connected HV patch panel to ground on floor behind it
196134 07/27/10 17:59 smacewan Main Detector Current Mode No Beam High Voltage Reference
196130 07/27/10 16:42 Kargiantoula Beam: Injector pedestals
196129 07/27/10 16:34 pqwang Main detector preamp offset recheck
196126 07/27/10 14:11 smacewan MD CM Preamp offsets
196117 07/27/10 13:40 leacock dslumi4 in halo1 all other lumi cm off
196110 07/27/10 13:22 gaskell Compton vacuum fixed
196091 07/27/10 11:59 pking Added an inverted T_stable signal to the TS0 VQWK
196086 07/27/10 11:33 W. Deconinck VESDA active again
196077 07/27/10 10:24 W. Deconinck VESDA 5 isolated on advice from fire protection engineer
196076 07/27/10 09:57 saw V2F "ADCs" on g0ioc4 scaler crate
196075 07/27/10 09:38 smithg beam dump diffuser & helium line windows replaced
196058 07/27/10 00:11 mack cavity triplet I-signals being looked at (BCM5/6)
Monday
196057 07/26/10 23:16 pking QwAnalysis/new has been updated to revision 1569
196056 07/26/10 22:04 pking Beginning update of the standard "QwAnalysis/new" analyzer on the cdaq machines
196052 07/26/10 21:52 leacock no longer seeing bands
196049 07/26/10 21:39 leacock lumi ADC misbehaving
196028 07/26/10 16:41 smacewan Main Detector in Current Mode
196027 07/26/10 15:52 beaufait qtor windows reset
196024 07/26/10 15:34 dalton Compton: Mode match
196021 07/26/10 15:20 kamyers run781 cosmic test
196020 07/26/10 14:58 smacewan Runs 778, 779 TS/MD cosmics
196015 07/26/10 14:12 smithg target vacuum problem resolved I think
196012 07/26/10 12:46 smacewan Plugged MD3- Signal Cable back in
196004 07/26/10 12:27 smithg Target: vacuum leak
196000 07/26/10 12:14 Buddhini/Han Replacing the fiber cable carrying heliciyt from the fiber splitter in rack 3H03B13 to 3H03B12
195999 07/26/10 12:01 kamyers run 768 trig scint test run
195998 07/26/10 11:45 kamyers run 767 another md test run
195993 07/26/10 10:59 saw Limit for attachments increased
195990 07/26/10 10:45 leacock lumi config change all cm now
195989 07/26/10 08:45 kenyon Look before you leap
195988 07/26/10 00:35 dalton Compton: Status of Compton optics
Sunday
195987 07/25/10 23:45 smithg Target: Target turbopump controller and CCG readout locations
195986 07/25/10 23:24 smithg target status: walking the lines
195985 07/25/10 22:58 saw Attachments working again
195978 07/25/10 22:18 smithg Target: vacuum motion
195970 07/25/10 21:14 smithg gem wall must go
195969 07/25/10 19:23 W. Deconinck Compton: c-compton was moved to the CH, now called ccomptl1
195965 07/25/10 17:10 Pitt Upstream lumi configuration change
195964 07/25/10 17:04 benesch target vacuum signal graph in elog
195957 07/25/10 13:27 smithg Target: scattering chamber vacuum plot
195956 07/25/10 13:24 smithg Target: scattering chamber vacuum plot
195955 07/25/10 12:05 smithg Target: scattering chamber vacuum
Saturday
195952 07/24/10 23:46 Jie Pan scanner positon calibration test
195947 07/24/10 22:27 pqwang Run 754, short run for scanner test
195946 07/24/10 22:14 pqwang short tracking mode run for calibrate scanner position
195945 07/24/10 19:48 Arshak GEM Detector.
195944 07/24/10 18:54 Don Jones Compton: progress on Compton laser
195940 07/24/10 16:26 Pitt End 749: Region 2 Cosmic Ray Run
195936 07/24/10 13:56 Buddhini Analysis: BCM noise studies results
195933 07/24/10 12:26 buddhini ET warnings
195921 07/24/10 08:39 pking/leckey Late entry: new patch panel between cage and 1st floor electronics room
195920 07/24/10 04:42 cdaq Run 733, scanner event mode test
195917 07/24/10 04:05 Nuruzzaman Missing Figures in Beam modulation test results
195916 07/24/10 04:02 Nuruzzaman Missing Figures in Beam modulation test results
195914 07/24/10 00:23 Figures 1 and 2 from entry 195910
195911 07/24/10 00:15 pking Test of HClog web entry with no attachments
195910 07/24/10 00:14 pking/jhoski Beam modulation test results
195909 07/24/10 00:12 pking Web entry form for HCLog is broken
Friday
195904 07/23/10 22:52 mack missing field notes from last BCM entry
195903 07/23/10 22:46 mack important: BCM1 and 2 gain settings for Qweak CM and EM
195901 07/23/10 20:48 pking Ramp signal was active but was accidentally set for sine wave in run 726
195899 07/23/10 20:28 Rakitha I think the problem is Fixed now!
195898 07/23/10 20:20 W. Deconinck Test of hclog template for shift summary
195896 07/23/10 19:31 kamyers TS/MD test runs
195894 07/23/10 18:41 pking Stopped run 724
195893 07/23/10 17:33 kamyers more cosmic tests
195891 07/23/10 16:46 saw HV GUI channel name changes
195890 07/23/10 16:21 kamyers run 722 ended
195889 07/23/10 14:34 saw Additional EPICS scalers added (g0rate16-32)
195888 07/23/10 14:04 kamyers Cosmic run 722 started
195887 07/23/10 13:43 kamyers run 721 ended
195886 07/23/10 12:46 kamyers Cosmic run 721 started
195885 07/23/10 12:40 kamyers trig scint hooked up to scaler "0" in ROC4
195884 07/23/10 12:11 kamyers Run 718 ended
195883 07/23/10 11:57 kamyers main detector run 717, 718
195882 07/23/10 11:34 smacewan Run 716 Completed
195881 07/23/10 11:26 smacewan Run 716, Main Detector Cosmic Run
195880 07/23/10 11:04 smacewan MD Reconfigured
195879 07/23/10 10:49 Pitt Run 715 done
195878 07/23/10 10:32 kamyers change to trigger scint cable configuration
195877 07/23/10 10:31 smacewan Switching Main Detector to Event Mode bases for ALL octants.
195876 07/23/10 10:10 paschke / da injector beam studies starting (with analysis on cdaql4)
195875 07/23/10 10:08 paschke missing patterns/events in devel analyzer Hel_Tree
195874 07/23/10 08:56 Pitt Tracking Run 715 - lumi HV/discriminator scan
195873 07/23/10 08:47 W. Deconinck DAQ: Rebooted qwvme9 and qwvme10
195872 07/23/10 08:10 Pitt Stop Run 710 - overnight tracking run
Thursday
195871 07/22/10 23:50 smacewan Very late entry: MD CM Bases HV off - cosmic plans for tomorrow
195870 07/22/10 23:32 Nuruzzaman Beam Modulation: Software Test
195869 07/22/10 23:32 dalton Compton: Status of Compton laser system
195868 07/22/10 22:23 mack overnite tracking run is taking a break
195867 07/22/10 22:15 mack cavity triplet analog outputs look funny
195866 07/22/10 19:20 Buddhini BCM analog signals and frequency signals are now connected to VQWK ADCs and scalers in Qweak cage.
195865 07/22/10 18:14 leacock run710 tracking run overnight
195862 07/22/10 15:53 gaskell Compton HV in Moller HV gui
195861 07/22/10 14:09 cdaq test run 704 for scanner
195860 07/22/10 12:52 brads Camera and other status information available off HClog page
195858 07/22/10 12:06 pking Completed update of "devel" analyser on cdaq machines
195857 07/22/10 12:06 jhlee update F1TDC status
195856 07/22/10 12:01 jhlee,smacew Run 701 and 702 for this test
195855 07/22/10 11:50 jhlee ROC4 F1TDC test
195854 07/22/10 11:47 Arshak GEM rotator and sliders.
195853 07/22/10 11:46 pking Beginning an update of "devel" QwAnalysis on cdaq machines
195852 07/22/10 11:40 jhlee ROC4 F1TDC replacement
195851 07/22/10 11:39 Leckey R3 Run Ended
195850 07/22/10 10:46 brads re: cdaql6 locked up, rebooted
195849 07/22/10 09:05 Leckey DAQ R3 Running on L6
195848 07/22/10 08:35 W. Deconinck DAQ: Soft reboot of qwvme10 (ROC10)
195847 07/22/10 08:24 W. Deconinck DAQ: Found cdaql6 locked up, rebooted
Wednesday
195846 07/21/10 23:34 mack cavity triplet signals cabled to 1st floor BCM rack
195845 07/21/10 20:45 mack unused slots in ROC2 vme crate are now blanked off
195844 07/21/10 19:15 Buddhini Not actually a lumi test. Nto related to any runs. This was just a test of the runstart script of RC.
195842 07/21/10 17:49 cdaq Ignore this entry:: End of Run 695:
195841 07/21/10 17:44 Buddhini Replaced the patch that carry BCM signals to the 2nd floor counting house. Connected bcm signals to new patch.
195840 07/21/10 17:12 mack BCM nomenclature update
195839 07/21/10 16:11 W. Deconinck DAQ: ROC9 rebooted using qwpowerstrip and qwvme9mon
195837 07/21/10 15:26 W. Deconinck DAQ: ROC9 crashes at end of run 690
195836 07/21/10 13:48 Armstrong Region3 in vertical (+90 degrees) orientation
195835 07/21/10 13:47 mack Musson et al have tuned BCM1 and BCM2 cavities
195834 07/21/10 06:58 paschke Compton: Compton laser installation, Summary 7/20 (late entry)
Tuesday
195831 07/20/10 22:48 mack both Musson cavity triplet receivers cabled to first floor counting house
195830 07/20/10 22:40 leacock run 681 scanner in OR
195826 07/20/10 17:49 brads Region 3 chambers remote threshold control
195824 07/20/10 17:42 brads A/C in doghouse moved to a plugin external to the doghouse
195823 07/20/10 17:34 mack BCM work in progress
195822 07/20/10 16:43 saw Mysql server restarted cdaql6
195821 07/20/10 13:49 leacock preamp gains
195815 07/20/10 09:05 Armstrong Trigger Scintillator correlates with VDC wires
Monday
195807 07/19/10 17:38 dalton Compton: Ordered a necessary shim
195806 07/19/10 17:18 brads A/C in doghouse plugged into 'clean' power
195805 07/19/10 17:17 Leckey R3 Scalers Connected
195804 07/19/10 16:38 Jie Pan scanner test run 652 start
195802 07/19/10 15:43 Peiqing wang All main detector PMT's were connected with current mode bases
195801 07/19/10 14:45 brads monticello working again
195800 07/19/10 14:36 Jie Pan Scanner test with VDC and main detectors
195799 07/19/10 14:34 Armstrong Scanner and VDCs play together nicely
195798 07/19/10 14:07 Nuruzzaman Monticello not working
195797 07/19/10 12:34 Arshak GEM ceiling was fixed.
195796 07/19/10 12:29 jhlee add how to access, reboot, and do power cycling ROCs in Qweak wiki
Sunday
195795 07/18/10 22:05 dalton Compton: Progress with the Compton Optics
195794 07/18/10 21:49 leacock changed fake helicity to 1 Hz
195792 07/18/10 21:43 leacock roc1 reboot
195791 07/18/10 21:40 leacock reboot roc2
195786 07/18/10 20:58 mack Hall C cavities ready for tuning
195785 07/18/10 20:31 leacock changed fake helicity to 1000Hz
195784 07/18/10 15:11 mack installed first set of radiation badges
195783 07/18/10 14:17 dalton Compton: harp and downstream bpm cables rerouted
195782 07/18/10 11:58 manos Reterminated cables part 2
195781 07/18/10 11:56 manos Reterminated cables part 1
Saturday
195780 07/17/10 23:56 mack DS Lumi preamp noise
195779 07/17/10 18:55 A. Tobias Compton: Alignment & Electronics Cabling continues ...
195778 07/17/10 18:53 W. Deconinck Compton: connected BPMs into DAQ
195777 07/17/10 17:19 leacock lumi disciminator scan with no beam
195776 07/17/10 16:25 gaskell survey monument holders
195775 07/17/10 13:54 Peiqing Wang Turned off MD high voltages
195774 07/17/10 13:25 gaskell Compton cable check part 2
195773 07/17/10 11:57 gaskell Compton cable check part 1
Friday
195772 07/16/10 21:47 mack Hall C BCM debugging
195771 07/16/10 18:59 dalton Compton: Alignment continues
195770 07/16/10 18:14 gaskell Compton BPM cable map
195769 07/16/10 18:09 gaskell BPM cabling
195768 07/16/10 17:24 kamyers/rob/ where are the scaler events?
195767 07/16/10 17:20 Nuruzzaman QTOR hall probe moved behind lentil
195766 07/16/10 16:36 kamyers Run 635 prescaler configuration
195765 07/16/10 16:24 kamyers Run 634 ended
195764 07/16/10 14:42 Jie Pan moved the scanner controller higher
195763 07/16/10 13:29 Leckey TS reset, again
195762 07/16/10 11:54 benesch Beam: if beam trips are useful for pedestals
195761 07/16/10 10:50 gaskell Moller detector check
195760 07/16/10 01:17 Gericke Analysis: FFT comparison
195759 07/16/10 01:02 Gericke Analysis: Run 583: FFT comparison for detector yield and asymmetry (common mode rejection)
195758 07/16/10 00:50 Gericke Analysis: Run 583: Runlet 4 beam trips
195757 07/16/10 00:40 Jie Pan scanner controller recovered
195756 07/16/10 00:01 dalton Compton: First light and some alignment done.
Thursday
195755 07/15/10 19:54 A. Tobias Compton: Laser Enclosure Curtain
195754 07/15/10 17:32 gaskell/kube Moller signal cables
195753 07/15/10 16:40 jhlee F1TDCs Status and Qweak battery sources
195752 07/15/10 16:08 pking Analysis: Updated analyser ("devel") on cdaq machines
195751 07/15/10 14:06 Leckey R3 Run 630 on cdaql6
195750 07/15/10 13:56 smacewan Reverted to old MainDetector TDC channel configuration
195749 07/15/10 11:07 gaskell Compton: Compton HV map
195748 07/15/10 10:06 birchall Consistency with measurement
195747 07/15/10 09:58 birchall rms width consistent with estimated event rate
195746 07/15/10 09:28 gaskell cable cleanup near Moller racks
195745 07/15/10 01:19 Gericke Analysis: Run 583: Aluminum main detector asymmetry
Wednesday
195744 07/14/10 21:10 dalton Ion pump stand knockdown
195743 07/14/10 21:05 Nuruzzaman Beam Modulation Installation and Test Summary
195742 07/14/10 20:32 dalton Compton: Status of Compton optics
195740 07/14/10 18:43 Jie Pan debug the scanner controller problem
195739 07/14/10 17:35 kamyers DC offset introduced to signals from ADC
195738 07/14/10 16:54 Leckey F1 Time Window
195737 07/14/10 16:53 Nuruzzaman End beam modulation tests
195736 07/14/10 16:43 smacewan Change of EM Mode Main Detector TDC channel
195735 07/14/10 16:18 jhlee a copy of the reply of the request for exclusion of portscan III
195734 07/14/10 15:30 mack BMod readout signals in epics
195733 07/14/10 15:21 Leckey F1 Time Window
195732 07/14/10 15:13 Buddhini Analysis: First look at the BPM signals through DAQ using weekend runs.
195731 07/14/10 14:15 Nuruzzaman Getting channel acess to epeics variable "BMOD2:CHAN0:RAMPWAVE"
195730 07/14/10 13:57 Nuruzzaman Beam modulation readouts
195729 07/14/10 12:58 Nuruzzaman Starting beam modulation tests
195728 07/14/10 12:22 jhlee F1TDC stauts at ROC9, ROC10, and ROC4
195727 07/14/10 11:51 Nuruzzaman Cables pulled and connections are done for ADC readbacks @ BSY for beam modulation
195726 07/14/10 11:41 pking Corrected an error in the cdaql6 login script
195725 07/14/10 11:16 jhlee all ROCs at Qweak Doghouse problems
195724 07/14/10 11:04 jhlee qwvme9
195723 07/14/10 11:01 jhlee this run is stoped for replacing one F1TDC
195722 07/14/10 10:04 Leckey cdaql6 DAQ Running for R3
195721 07/14/10 10:04 Nuruzzaman JLab made ADC card is installed @ BSY for beam modulation readouts
195720 07/14/10 09:02 Leckey R3 Run 613 Complete
195716 07/14/10 01:32 gericke Analysis: Run 583 "Current Mode" MD Diagnostic Analysis I (some plots)
195715 07/14/10 01:28 gericke Analysis: Run 583 "Current Mode" MD Diagnostic Analysis I (some plots)
Tuesday
195714 07/13/10 19:29 smacewan MD Event Mode ADC Signals Lost+Found
195713 07/13/10 17:21 Leckey cdaql6 R3 Run All Night
195712 07/13/10 17:16 Nuruzzaman Electron Detector Vacuum Can is @ JLab now
195711 07/13/10 15:35 Leckey R3 Run 617 on cdaql6 Active Now
195710 07/13/10 13:30 Leckey cdaql6 R3 Run Complete
195707 07/13/10 09:00 leacock target high power heater alarm
195706 07/13/10 00:38 jhlee Try to compile ROOT with different options
Monday
195705 07/12/10 18:12 mack Where Does the MD PMT Pulse Height Go To?
195704 07/12/10 17:00 pking Analyzer performance on cdaq machines
195703 07/12/10 14:37 pking cdaql6 is locked up
195702 07/12/10 14:23 kenyon QTor Power Supply
195701 07/12/10 14:12 jhlee one more powerstrip at Qweak Doghouse
195700 07/12/10 14:11 jhlee Lan configuration at the doghouse (v1.3)
195699 07/12/10 13:54 kenyon Comptom power supply/magnets
195698 07/12/10 12:57 jhlee powerstrips' configuration at Qweak Doghouse
Sunday
195697 07/11/10 19:45 Armstrong QTor Magnet scan - more detailed results
195695 07/11/10 16:01 spage Day Shift Summary
195694 07/11/10 16:00 cdaq Beam Time Accounting
195693 07/11/10 15:56 spage Scanner HV
195692 07/11/10 15:32 Rakitha Scanner PMT high voltage set to 1500V
195691 07/11/10 15:31 spage HV off
195690 07/11/10 14:18 saw Hall to go into restricted access around midnight
195687 07/11/10 13:55 pking Flipped all of the trigger supervisor scaler control inputs
195686 07/11/10 13:10 spage target position
195685 07/11/10 12:20 pking Found the MPS polarity had been flipped from what it should have been.
195684 07/11/10 12:00 spage water photos
195683 07/11/10 11:46 spage water follow up
195682 07/11/10 11:22 spage water leak in hall C power supply
195681 07/11/10 10:42 Rakitha Qweak Scanner signals in current mode
195680 07/11/10 10:38 Buddhini Hall C is in Controlled Acess
195679 07/11/10 10:27 Buddhini QTOR Tripped
195678 07/11/10 10:22 spage beam trip, QTOR trip, raster change
195677 07/11/10 10:04 spage beam positions, runs 585, 586
195676 07/11/10 09:45 spage scanner HV turned back on
195675 07/11/10 09:25 Rakitha no_key
195674 07/11/10 09:13 spage plan for today
195673 07/11/10 08:46 spage beam current check , beam position change
195672 07/11/10 08:46 buddhini Run 584 : Current Mode run. 135 nA Beam Current, 2x2 raster, 1 mm Al target, QTOR = 8937 A
195671 07/11/10 08:26 spage beam positions during run 583
195670 07/11/10 08:13 cdaq Beam Time Accounting
195669 07/11/10 08:11 spayde Owl Shift Summary (Run List)
195668 07/11/10 08:06 spayde Owl Shift Summary (Take Two)
195667 07/11/10 08:05 spayde Owl Shift Summary
195665 07/11/10 07:38 spayde TOSP Guidance on Tungsten Water Flow
195664 07/11/10 07:06 spayde Visual Inspection of Tungsten Water Chiller
195663 07/11/10 06:40 spayde Going to Controlled Access
195661 07/11/10 06:07 spayde Runs for R2 Tracking Program
195660 07/11/10 05:59 spayde Beam: Increased Beam Current
195659 07/11/10 05:58 davidg Followup to tungsten waterflow faults
195658 07/11/10 05:57 Pitt Region leakage currents at different voltages
195657 07/11/10 05:22 spayde Requested Beam Off
195656 07/11/10 05:17 brads re: Effect of Hall A
195655 07/11/10 05:16 spayde Switching from Tracking to Parity Mode
195654 07/11/10 04:46 Pitt No Hokie4 Fast OR Scaler
195653 07/11/10 04:35 Pitt Lumi discriminator scan description - run 577
195652 07/11/10 04:30 Pitt Region 2 leakage currents for Run 578
195651 07/11/10 04:12 spayde Turning Detectors On
195648 07/11/10 03:53 Pitt Response of halo monitors to IHA307A and IHA307B harp scans
195647 07/11/10 03:51 spayde LUMI Response to Harp Scans
195646 07/11/10 03:41 spayde Asking MCC to Run Harps
195645 07/11/10 03:22 spayde Turning Off Detectors
195644 07/11/10 03:14 Pitt Effect of Hall A
195643 07/11/10 03:11 spayde Hall A Beam Back at 120 uA
195642 07/11/10 03:07 spayde Correction
195641 07/11/10 03:02 spayde Turning of R2 Wire Chambers
195640 07/11/10 02:53 spayde Changing R2 Wire Chamber Voltages
195639 07/11/10 02:33 spayde Scintillator Rates at 150 pA
195638 07/11/10 02:23 spayde Turning on R2 Chambers
195637 07/11/10 02:05 spayde Reducing Beam Current
195636 07/11/10 01:56 Jie Pan scanner QDC channels might mixed up with trigger scintillator QDC channels
195635 07/11/10 01:52 mack MD ADC gate timing looks good
195634 07/11/10 01:52 spayde Some Amount of Beam in Hall
195633 07/11/10 01:44 rob qtor fine scan around elastic peak
195632 07/11/10 01:35 rob illustrated QTor guide
195631 07/11/10 01:11 Pitt EPICS scaler configuration for the low current running period
195630 07/11/10 01:09 mack MD analog signals with beam at nominal QTOR current (no more steenking cosmic rays)
195629 07/11/10 00:58 Pitt Region 2 Scintillator Setup for Low Current Running
195628 07/11/10 00:26 mack first event mode QTOR scan run plan used earlier this evening
195627 07/11/10 00:18 cdaq Beam Time Accounting
195626 07/11/10 00:16 spayde Out of Controlled Access
195625 07/11/10 00:16 spayde Turning off R3 Trigger Scintillators
195624 07/11/10 00:02 R. Subedi Shift Summary
Saturday
195623 07/10/10 23:42 mack RIII tripped off approaching 1000A from above
195622 07/10/10 23:06 rob begin moller electron region field scan
195621 07/10/10 22:47 rob qtor maximum current is 9100 A
195620 07/10/10 22:34 rob up again following power trip
195619 07/10/10 22:28 rob and by "during 566", I of course meant "during 565"
195618 07/10/10 22:26 rob power blip during run 566
195617 07/10/10 22:23 cdaq TEST::Ignore this entry:End of Run 554:
195616 07/10/10 22:21 Armstrong Region 3 VDCs left on
195613 07/10/10 21:49 mack efficiency for a significant MD analog signal with a GWUTscint triggers
195612 07/10/10 21:43 cdaq TEST::End of Run 554:
195611 07/10/10 21:37 birchall
195610 07/10/10 21:30 rob wandering in trigger rates and ipm3h09{,b}.{xy] positions before and during hall a tune
195609 07/10/10 21:19 rob second qtor reset
195608 07/10/10 21:17 kamyers trigger scintillator signals with beam -- late entry
195607 07/10/10 20:58 Armstrong QTor Magnet scan, partial results
195606 07/10/10 20:55 W. Deconinck Firefox weave sync disabled
195605 07/10/10 20:55 Armstrong QTor ramp up
195604 07/10/10 20:55 birchall Rates from Al target
195603 07/10/10 20:44 cdaq TEST::IGNORE::End of Run 554:
195602 07/10/10 20:43 Armstrong Late Entry - Tungsten Plug water flow
195601 07/10/10 20:36 rob qtor crash photos link
195600 07/10/10 20:36 cdaq TEST::IGNORE::End of Run 554:
195599 07/10/10 20:35 mack/king first few hours on swing shift spent getting ready for QTOR scan
195598 07/10/10 20:34 Armstrong VDCs tripped; QTor controls lost again
195597 07/10/10 20:31 rob qtor crash photos
195596 07/10/10 20:07 jhlee Please, ignore the entries of the End of Run 554:
195595 07/10/10 20:02 Armstrong Interim log of QTor scan
195594 07/10/10 20:00 mack/buddhin BCM1/2 debugging
195593 07/10/10 19:58 mack/buddhin BCM1/2 debugging
195588 07/10/10 19:32 Armstrong Magnet controls freeze
195587 07/10/10 19:19 W. Deconinck Firefox weave sync for cdaq (testing)
195586 07/10/10 19:17 Armstrong QTor magnet weirdness
195585 07/10/10 19:04 Armstrong Magnet current scan underway
195584 07/10/10 18:52 Armstrong Magnet to 8043.3 A
195582 07/10/10 18:47 rob 4 MHz clock problem resolved for now
195581 07/10/10 18:38 W. Deconinck End of run 545: trigger issues
195580 07/10/10 18:30 rob EPICS scaler rate jump
195578 07/10/10 18:24 Armstrong Maybe not a beam change originally...
195577 07/10/10 18:12 smacewan Attempt to Determine Scanner Rate
195576 07/10/10 18:08 Armstrong Changed beam current...
195575 07/10/10 17:55 Armstrong 2nd try
195574 07/10/10 17:53 Armstrong stripchart
195573 07/10/10 17:50 Armstrong Beam current jump?
195572 07/10/10 17:36 Armstrong Region 3 VDCs at 50 nA
195571 07/10/10 17:36 cdaq Run /local/data1/track_noR1_545.dat.0: Ignore the runnumber in the log
195570 07/10/10 17:34 cdaq Run : Ignore the runnumber in the log
195569 07/10/10 17:32 cdaq Run : Ignore the runnumber in the log
195568 07/10/10 17:30 cdaq Run : Ignore the runnumber in the log
195566 07/10/10 17:28 rob Beam: main detector trigger OR rates
195565 07/10/10 17:27 cdaq Run : Ignore the runnumber in the log
195564 07/10/10 17:26 cdaq Run : Ignore the runnumber in the log
195556 07/10/10 16:46 kamyers correction to TS OR rate entry
195555 07/10/10 16:30 spage Day Shift Summary
195554 07/10/10 16:25 kamyers TS rate with target position
195553 07/10/10 16:20 cdaq Beam Time Accounting
195551 07/10/10 16:06 smithg Target: Moved tgt position back to y=-41 mm
195549 07/10/10 16:04 smithg Target: Moved tgt position to y=-43 mm
195548 07/10/10 16:01 smithg Target: Moved tgt position to y=-41mm
195547 07/10/10 15:50 spage Effect of Hall A
195546 07/10/10 15:46 Buddhini Testing the run info entry logs. Please ignore the information on these!
195538 07/10/10 15:35 Rakitha A summary of the QwAnalysis performance tests done on the cdaql6/ou-qweak5 machines
195537 07/10/10 15:26 smithg Target: Moved tgt to y=-39 to try and hit one foil
195535 07/10/10 15:13 smithg Target: Moved tgt to y=-35 to try and hit one foil
195534 07/10/10 15:04 smithg Target: Moved tgt to y=-35 to try and hit one foil
195531 07/10/10 14:46 spage trigger scintillator vs beam current
195530 07/10/10 14:45 spage BPM behaviour
195529 07/10/10 14:13 mack ion chamber snapshot
195528 07/10/10 14:13 Pitt Current mode lumis are on
195527 07/10/10 14:12 spage beam current and bpm's
195526 07/10/10 13:59 spage resteer beam, reduce intensity
195525 07/10/10 13:49 saw BCMs not working
195524 07/10/10 13:21 saw BCM gain setting set to 5
195523 07/10/10 13:19 spage Beam: Accounting for Beam Use
195522 07/10/10 13:15 saw Betabrite
195521 07/10/10 13:02 smithg Target: some target screens
195520 07/10/10 12:46 smithg Target: moved to lifter=-57 mm=5 foil optics target in
195519 07/10/10 12:41 Pitt Beam: Halo Monitor Status
195518 07/10/10 12:39 spage The raster really works
195517 07/10/10 12:39 saw Qtor PS crash, picture request
195516 07/10/10 12:31 saw Hall C archiver restarted
195515 07/10/10 11:53 spage QTOR reset and turned up to 8940 A - nominal setting
195514 07/10/10 11:48 kamyers qtor ramped to full current
195513 07/10/10 11:40 Buddhini Reset the trip from the main gui
195512 07/10/10 11:31 benesch Beam: URLs of my elog entries
195511 07/10/10 11:22 spage getting ready for target
195510 07/10/10 11:05 Buddhini Turned on the halos 5,6,7,8
195509 07/10/10 11:00 spage beam tune ok now, as last week
195508 07/10/10 10:27 Buddhini MCC looked in to the half closed 3H04 valve : It does not exsist..
195507 07/10/10 10:12 Jie Pan Offset for raster Y was not set properly?
195506 07/10/10 10:05 saw Hall Probe scale
195505 07/10/10 09:53 Buddhini run 535 : Parity run with halos 5 6 7 8 on.
195504 07/10/10 09:53 spage what is going on with the beam?
195503 07/10/10 09:40 Buddhini Halos on 'trip' status
195502 07/10/10 09:39 spage halo monitors trip
195501 07/10/10 09:22 spage short term day shift plan
195500 07/10/10 09:21 spage short term day shift plan
195499 07/10/10 08:58 Buddhini Turned off the halo monitors
195498 07/10/10 08:27 spayde Cannot See Beam at Harp 3H07
195497 07/10/10 08:18 spayde Owl Shift Summary
195496 07/10/10 08:13 cdaq Beam Time Accounting
195495 07/10/10 07:37 W. Deconinck Beam: Jay will try a 3H07 harp scan
195494 07/10/10 07:31 spayde Halo 4 Trips with No Beam
195493 07/10/10 07:16 gaskell raster x should be flat too
195492 07/10/10 07:15 spayde Current HV Situation
195491 07/10/10 07:11 spayde Should Say Halo 4
195490 07/10/10 07:01 spayde Halo 3 Keeps Tripping Off
195489 07/10/10 06:54 spayde Halo 4 Tripped Off
195488 07/10/10 06:46 spayde Beam: Continuing Troubles Viewing Beam on Dump Viewer
195487 07/10/10 06:31 W. Deconinck Analysis: Raster decoding and analysis
195486 07/10/10 06:24 Spayde Beam: MCC Having Trouble Imaging Beam on Dump Viewer
195485 07/10/10 05:46 spayde Beam: Going to Tune Mode
195484 07/10/10 05:33 spayde Beam: Verifying Raster
195481 07/10/10 04:53 pking Raster ADC is working now; pulser is plugged in as trigger 8
195480 07/10/10 04:30 spayde/mahur QTOR Ramped to 448 A
195479 07/10/10 04:12 pking Tracking DAQ status for tonight
195478 07/10/10 04:10 spayde Request Controlled Access for QTOR Ramp
195477 07/10/10 03:44 spayde Unable to Ramp QTOR
195476 07/10/10 03:27 W. Deconinck Beam current and positions
195475 07/10/10 03:18 spayde Trying to See Beam on BCMs
195474 07/10/10 03:01 W. Deconinck hclog command works now
195473 07/10/10 02:56 spayde Beam: MCC Has Tuned Up Our Beam
195472 07/10/10 02:48 pking Parity DAQ status for tonight
195471 07/10/10 02:02 spayde/mack Radiation Levels Around the Compton
195470 07/10/10 02:00 spayde Beam: MCC Sending Tune Beam
195469 07/10/10 01:41 spayde/mack Beam: Moller Quad Situation Resolved
195468 07/10/10 01:22 W. Deconinck Beam: Dave Gaskell assisting in restart of power supply by phone
195467 07/10/10 01:13 W. Deconinck Firefox profile script now uses the most recent stable version of firefox
195466 07/10/10 00:54 W. Deconinck Beam: Escorted access for Mack and Spayde to reset out 1st Moller quad power supply
195465 07/10/10 00:34 leacock lumi configuration for weekend run and halo update
195464 07/10/10 00:31 pking Tracking DAQ busy is ~300us per event
195463 07/10/10 00:12 cdaq Beam Time Accounting
195462 07/10/10 00:06 mack FR screen, captured with xv
195461 07/10/10 00:01 R. Subedi Shift Summary
Friday
195460 07/09/10 23:27 pking Changing the qwvmets CPU
195459 07/09/10 22:47 R. Subedi Status update
195458 07/09/10 22:11 silviu Target: optics targets heating profile from 2 uA beam
195457 07/09/10 21:26 Pitt Halo monitor: correction
195456 07/09/10 21:24 Pitt EPICS scaler configuration
195455 07/09/10 21:20 W. Deconinck Food was provided to the hungry shift-workers
195454 07/09/10 21:19 Pitt Beam: Halo monitor configuration
195453 07/09/10 21:02 Buddhini All of the available HallC BPMs are now connected to Qweak Parity DAQ!
195452 07/09/10 20:34 kamyers Trig Scint test runs: 484 and 485
195451 07/09/10 19:48 W. Deconinck Beam: Hall C in beam permit
195450 07/09/10 18:36 W. Deconinck Beam: Link to Jay's plans for tonight
195449 07/09/10 18:33 W. Deconinck Beam: Accelerator RF separator issue, repair estimated 8pm
195448 07/09/10 18:25 mgericke analyzer performance
195447 07/09/10 18:05 Rakitha qweak analyzer performance checks on cdaql6 has done (At least for now!)
195446 07/09/10 17:47 birchall QTOR scan for e-p elastics
195444 07/09/10 17:35 R. Subedi Hall in Controlled Access
195442 07/09/10 17:05 mgericke Scanner status
195441 07/09/10 16:32 smithg Beam: exit window chiller broken
195440 07/09/10 15:59 smithg Beam: exit window chiller broken
195437 07/09/10 15:20 jhlee fixed format for a copy of the reply of the request for exclusion of portscan II
195436 07/09/10 15:13 jhlee a copy of the reply of the request for exclusion of portscan II
195435 07/09/10 15:06 brads Tracking detector checklist completed, please note the exceptions
195434 07/09/10 15:06 kamyers QTOR scan for Al target - Mollers
195433 07/09/10 15:02 jhlee not really better :-(
195432 07/09/10 14:59 jhlee a better format for Replace one F1TDC (Slot6, ROC9) with other
195431 07/09/10 14:50 jhlee Replace one F1TDC (Slot6, ROC9) with other
195430 07/09/10 14:49 rob late entry: main detector event mode trigger is much better
195429 07/09/10 14:45 jhlee Replace one F1TDC (Slot6, ROC9) with other
195428 07/09/10 14:34 Rakitha Connection reset by peer, Connection to cdaql6.jlab.org closed while running valgrind
195427 07/09/10 14:19 birchall QTOR scan for Al target
195426 07/09/10 14:19 birchall QTOR scan for Al target
195425 07/09/10 13:44 pking cdaql6 locked up; rebooting
195424 07/09/10 13:22 mack Getting ready for MD checklist
195423 07/09/10 13:04 pking DAQ in use starting to reconfigure for CODA 2.6.1
195422 07/09/10 11:23 pking DAQ in use for R3 tests
195421 07/09/10 11:14 Buddhini Moved the scanner signals to the new ADC in TS crate
195420 07/09/10 11:04 saw xv installed on cdaql machines
195419 07/09/10 10:52 pking/buddhi Installed VQWK in TS crate
195418 07/09/10 10:50 mack BCM17 connected
195417 07/09/10 09:49 Rakitha qweak analyzer performance checks started on cdaql6
195416 07/09/10 09:24 pking Run 473 ended at 05:48 with EB error
195415 07/09/10 00:44 Don Jones Compton: Compton laser
Thursday
195414 07/08/10 22:14 rob Run 473: main detector cosmics
195413 07/08/10 21:20 rob event builder unstable on cdaql6?
195412 07/08/10 19:57 Rak qweak analyzer performance checks ended on cdaql6
195411 07/08/10 19:40 Nuruzzaman Took a run for beam modulation test with ts_2crate configuration, MPS helicity
195410 07/08/10 19:15 Rakitha qweak analyzer performance checks started on cdaql6
195409 07/08/10 18:31 Buddhini Reboot TS , roc1 and roc2
195408 07/08/10 18:22 Kargiantoula Beam: PITA scans from July 7
195407 07/08/10 17:07 jhlee the problem is....
195406 07/08/10 16:28 jhlee/nur reboot qwvme2
195405 07/08/10 16:20 jhoskins R3 rotator arms in out position.
195404 07/08/10 14:55 jhoskins R3 rotator linear motion fixed
195403 07/08/10 13:50 Nuruzzaman Error in CODA with configuration roc2_ts
195402 07/08/10 13:44 gaskell BCM 3 not connected
195401 07/08/10 13:30 Nuruzzaman Beam Modulation Signals to Q-weak ADCs with Hardware Trigger
195400 07/08/10 13:21 jhlee put F1TDC configuration into CODA stream
195399 07/08/10 12:56 pking Total propagation delay of current TrigSup configuration and timing of ADC gate
195398 07/08/10 12:42 pking Installed the K-Bus interface in qwvmets
195397 07/08/10 12:39 wdconinc Compton: BCM1/2/3 and unser in Compton DAQ
195396 07/08/10 12:38 pking/jhlee Switched polarity of TrigSupervisor inputs
195393 07/08/10 11:32 Armstrong Beam: Hall C Songsheets
195392 07/08/10 09:54 spayde/bgv/u Patch Panel Between Electronics Cage and Hall C Racks Terminated
195391 07/08/10 08:34 hansknec inconclusive
Wednesday
195390 07/07/10 22:13 rob main detector event mode trigger sucks
195389 07/07/10 21:27 pking Late entry: cable for BPMs in BSY service building has connectors
195388 07/07/10 18:56 Armstrong Region 3 HV supplies moved
195386 07/07/10 17:53 paschke Beam: Source RHWP mover appears broken
195385 07/07/10 17:09 dalton Compton: Equipment arrives, installation begins
195384 07/07/10 15:52 Nuruzzaman Beam Modulation Signals to Q-weak ADCs
195383 07/07/10 14:47 mack Wrong Hall probe is in
195382 07/07/10 14:08 mack Installed NIM crate in Rack 1 for RIII HV
195381 07/07/10 13:11 rob reorganized generation of fake mps/helicity triggers
195380 07/07/10 12:48 Armstrong don't turn on QTor
195379 07/07/10 10:44 Leckey Tracking R3 Run cdaql6
195378 07/07/10 09:13 pking cdaql4 will be rebooted today at about noon.
195377 07/07/10 00:41 mack proposal for initial rad badge distribution
Tuesday
195376 07/06/10 23:16 saw Qtor current and field stability
195375 07/06/10 23:08 saw Qtor Trip problem probably fixed
195374 07/06/10 20:51 rob main detector event-mode trigger: and-or or or-or
195373 07/06/10 18:59 rob helicity real-or-fake in data stream, partial implementation
195372 07/06/10 13:35 mack MD event mode HV turned on near beginning of run 419
195371 07/06/10 13:20 paschke analysis speed
195370 07/06/10 12:56 Armstrong more Region 3 cosmic runs
195369 07/06/10 12:27 pking Please do not leave the electronics cage open if you're not working there
195368 07/06/10 10:33 dalton Helicity frequency changed
195367 07/06/10 09:45 Armstrong Cosmic Run - Region 3
195366 07/06/10 08:59 Armstrong Coordinating CODA
195365 07/06/10 08:14 dalton Beam: Starting injector DAQ
Monday
195364 07/05/10 23:37 mack MD analog signals
195363 07/05/10 19:38 saw Hall in restricted access
195362 07/05/10 18:11 jonesdc Compton: preparation for laser installation
195361 07/05/10 17:15 mack Next time set QTOR to 700-900A for Moellers - now that the fog of battle has lifted
195360 07/05/10 17:08 kamyers trigger scintillator signal with beam on
195359 07/05/10 16:42 dalton Hall C going to controlled access
195358 07/05/10 16:12 spage end of weekend run - "Fix List"
195357 07/05/10 15:50 leacock analog lumi signals
195356 07/05/10 15:38 leacock Day Shift Summary
195355 07/05/10 15:15 Armstrong VDC currents - late entry
195354 07/05/10 15:00 Armstrong Target out
195353 07/05/10 15:00 smithg Target: Removed tgt. Rates flatlined.
195350 07/05/10 14:29 leacock r2 high voltage scan
195349 07/05/10 14:16 leacock beam on ~200pA
195348 07/05/10 14:16 leacock access to reset magnet controls
195347 07/05/10 14:05 Armstrong Striptool annoyance
195346 07/05/10 13:56 Armstrong screenshot of magnet GUI
195345 07/05/10 13:55 Armstrong Beam off rates
195344 07/05/10 13:53 Pitt Region 2 Beam left versus Beam right - with attachment this time
195343 07/05/10 13:49 Pitt Region 2 Beam left versus Beam Right Scintillator Rates
195342 07/05/10 13:44 Pitt EPICS Scaler Configuration Change
195341 07/05/10 13:40 leacock halo monitor rate
195340 07/05/10 13:37 saw Please reset QTOR PS control computer when possible
195339 07/05/10 13:31 Armstrong Rates with QTOR at 250 A
195338 07/05/10 13:28 leacock lumi rates
195337 07/05/10 13:24 leacock halo monitor makeup
195336 07/05/10 13:17 Nuruzzaman How to for QTOR and Beam Modulation
195335 07/05/10 13:05 saw Magnet trip not necessarily due to Ground Fault
195334 07/05/10 13:00 Nuruzzaman QTOR Hall Probe Field Measurement
195333 07/05/10 12:50 mack ground fault
195332 07/05/10 12:32 Armstrong QTOR magnet trip
195331 07/05/10 12:11 leacock lumi current draw at 300pA
195330 07/05/10 12:10 leacock lumi rates increase when hall a has no beam
195329 07/05/10 12:01 kamyers ramped to 2000A, not 3000A
195328 07/05/10 11:52 kamyers trigger scintillator rates wth QTOR current
195327 07/05/10 11:48 leacock monticello (beam information) using edmmonticello
195326 07/05/10 11:45 leacock monticello (beam information) not working consistently on cdaqs
195325 07/05/10 11:14 leacock beam on ~11am
195324 07/05/10 11:12 leacock lumi rates at nominal 300pA
195323 07/05/10 11:08 Armstrong Run 407
195322 07/05/10 10:21 leacock dslumi 7 tripped and won't go back to operating voltage
195321 07/05/10 09:31 spage QTOR set to 6000 A
195320 07/05/10 09:30 Pitt EPICS scaler assignments - updated
195319 07/05/10 09:22 leacock run 406 helicity window trigger
195318 07/05/10 09:17 leacock fake mps on 2nd floor cage
195317 07/05/10 09:08 leacock QTor tripped
195316 07/05/10 08:59 spage QTOR set to 8000 A
195315 07/05/10 08:59 leacock gas shed ethane alarm
195314 07/05/10 08:59 Armstrong R2 and R3 chamber gas flowing
195312 07/05/10 08:45 leacock QTor at 8000 A
195311 07/05/10 08:44 leacock controlled access to increase QTor current to 8000 A
195309 07/05/10 07:35 Darko Owl Shift Summary
195308 07/05/10 06:58 spage QTOR
195307 07/05/10 06:56 spage QTOR behaviour
195305 07/05/10 05:58 rob run 401: md triggers and r2 triggers
195304 07/05/10 05:40 rob qtor trip, continued
195303 07/05/10 05:33 rob run 402: r2 .and. quartz trigger
195302 07/05/10 04:09 michaelm Analysis: re:turning off hall A
195301 07/05/10 03:52 rob plausible R2+quartz coincidence on scope
195299 07/05/10 02:37 Pitt Hokie 4 trip
195298 07/05/10 02:37 mack turning off Hall A
195297 07/05/10 02:27 Pitt Information about lumis being used as current monitor
195296 07/05/10 02:20 Pitt Data for lumi study
195295 07/05/10 02:16 Pitt Turning on Regin 2 chambers
195294 07/05/10 02:04 Darko Qtor magnet trips
195293 07/05/10 01:53 mack missing attachment from previous entry
195292 07/05/10 01:47 mack MD activities on swing shift
195291 07/05/10 01:43 rob beam is back on
195290 07/05/10 01:38 rob beam off for r2 again
195289 07/05/10 01:00 Darko Beam: Beam on
195288 07/05/10 00:37 rob beam off to power up r2 chambers
195287 07/05/10 00:25 spayde Swing Shift Summary
195286 07/05/10 00:12 spayde/pitt Beam: LUMI Rate Study
Sunday
195285 07/04/10 23:54 smithg Target: no change in tgt temp
195284 07/04/10 23:13 spayde First Beam on a Qweak Target
195283 07/04/10 23:04 spayde Changed Raster Size
195282 07/04/10 22:50 smithg Target: Put in optics target
195281 07/04/10 22:27 Pitt EPICS Scaler assignments
195280 07/04/10 22:07 Pitt Change Detectors that are on
195279 07/04/10 21:24 Pitt High voltages off
195278 07/04/10 21:22 Pitt Some high voltages turned on
195277 07/04/10 21:18 spayde Beam: MCC Tuning Up 250 pA
195276 07/04/10 21:05 spayde Beam: Evidence of Beam in Hall
195275 07/04/10 20:36 spayde MCC Starting to Send Beam
195274 07/04/10 19:50 mack QTOR Hall probe set to AUTORANGE during short access; small water leaks
195273 07/04/10 18:55 spayde Status Update
195272 07/04/10 16:45 Nuruzzaman Hall-C Main Control Menu is showing error on "cdaql3"
195271 07/04/10 16:33 Nuruzzaman QTOR magnetic field plot
195270 07/04/10 15:59 mack MD event mode HV disabled again
195269 07/04/10 15:44 jhoskins Run Summary::070410
195268 07/04/10 15:40 pking Trigger inputs and prescales for ts_2crate and track_noR1 run types
195267 07/04/10 15:17 mack event mode HV temporarily enabled
195266 07/04/10 14:31 Pitt EPICS scaler: Trigger Scintillator OR signal
195265 07/04/10 14:17 page Beam: CHL trip - no beam - what to do next.
195264 07/04/10 14:09 mack Lakeshore Hall probe
195263 07/04/10 13:43 saw Qtor reset in hall
195262 07/04/10 13:36 Pitt Some crude rate predictions for the various regions for 5 mm Al target
195261 07/04/10 13:27 mack QTOR current - with small correction for present beam energy
195260 07/04/10 13:11 saw QTOR tripped
195259 07/04/10 12:58 saw Qtor set to 8500 A
195258 07/04/10 11:56 jhoskins beam not steering at 5KA
195257 07/04/10 11:45 Pitt EPICS Scaler updated
195256 07/04/10 11:37 Pitt Beam: Turn on selected halo and lumi monitors
195255 07/04/10 11:20 pking Cleaning cdaq home directory
195254 07/04/10 10:37 saw Qtor Control computer tripped again
195253 07/04/10 10:23 birchall Cerenkov cars
195252 07/04/10 10:20 saw Qtor turned on
195251 07/04/10 10:17 birchall QTOR current
195250 07/04/10 09:52 jhoskins QTOR ramp
195249 07/04/10 08:25 spage Sunday morning plans
195248 07/04/10 07:50 Leckey CW Beam Soon
195247 07/04/10 07:33 Leckey Summary of Owl Shift
195246 07/04/10 06:02 Leckey Beam to end of Hall C
195245 07/04/10 05:30 Leckey Beam Permit
195244 07/04/10 05:18 Leckey First Beam
195243 07/04/10 03:21 Leckey Beam Permit
Saturday
195242 07/03/10 23:59 spayde Swing Shift Summary
195241 07/03/10 23:37 spayde Hall in Controlled Access
195240 07/03/10 23:31 pking Run 388 tests all four event mode trigger sources
195239 07/03/10 23:19 pking More tests of combined tracking run type
195238 07/03/10 22:35 pking Run 385 uses TS0/ROC4/ROC9/ROC10
195237 07/03/10 22:14 pking Plugged ROC4 into TS branch 4.
195236 07/03/10 22:06 spayde More FSD Trouble
195235 07/03/10 22:05 pking Changed ROC4 to run on the cdaql6 DAQ process
195234 07/03/10 21:29 spayde Hall C Going to Beam Permit
195233 07/03/10 21:24 spayde FSD Situation Resolved
195232 07/03/10 20:40 gaskell more on vacuum
195231 07/03/10 20:34 Pitt Status of HV for VT1,2,3 Crates
195230 07/03/10 20:17 benesch vacuum and FSD situation, as I understand it
195229 07/03/10 19:59 mack The Unser monitor is alive!
195228 07/03/10 19:14 pking Added GWU ADC to ROC4
195227 07/03/10 19:11 kamyers trigger scintillator HV turned off
195226 07/03/10 18:52 pking Temporary change in ROC4 F1TDC trigger delay
195225 07/03/10 18:04 spayde Target Vacuum
195224 07/03/10 16:10 Benesch projected vacuum at 8pm
195223 07/03/10 15:20 Pitt EPICS Scaler GUI
195222 07/03/10 14:39 benesch couldn't add vacuum signals to archiver temporarily
195221 07/03/10 14:35 mack Unser calibration wire is disconnected
195220 07/03/10 13:36 tforest scaler in tracking DAQ?
195219 07/03/10 13:23 mack MD summary of recent LED+battery runs
195218 07/03/10 13:04 pking First runs with the new scaler configuration
195217 07/03/10 12:59 pking Added 31MHz clock to beamline scaler and EPICS scaler
195216 07/03/10 12:37 birchall Hall C in controlled access
195215 07/03/10 12:09 pking Added LNE signal for DH scalers on PP416
195214 07/03/10 12:03 benesch VCG3H09ATr vacuum signal
195213 07/03/10 11:52 birchall Sweep of hall C
195212 07/03/10 11:28 kenyon Exit window chiller
195211 07/03/10 11:25 smithg projected vacuum should be ~ok at 8PM
195210 07/03/10 09:57 gaskell Scattering chamber leak check ok
195209 07/03/10 09:39 birchall Target: Jay's plot of target vacuum overnight
195208 07/03/10 08:37 birchall Target: Target chamber vacuum
Friday
195207 07/02/10 20:03 gaskell Target vacuum status
195206 07/02/10 19:54 mack disabled all MD high voltages for now
195205 07/02/10 19:22 pking Removed the "helicity leakage circuit"
195204 07/02/10 19:07 szh GEM cable length
195203 07/02/10 18:46 gaskell Halo target retracted, controls disconnected
195202 07/02/10 18:16 saw Qtor and power supply status
195201 07/02/10 18:03 mack Long term stability of MD offsets and battery signals
195200 07/02/10 17:54 Nuruzzaman Beam Modulation Function Generator Tests
195199 07/02/10 17:38 mgericke Analysis: Short pedestal run 375
195198 07/02/10 17:05 Buddhini Analysis: Results from the helicity pickup studies on main detector signals ( based on the first 5 mins of data )
195197 07/02/10 16:53 pking Notes from the ROC4 studies this morning.
195196 07/02/10 16:32 Shelley Page Beam: Hall C status update
195195 07/02/10 16:09 Rakitha Updated map for Trigger signals from Qweak Cage to Dog house
195192 07/02/10 14:34 rob md configuration change: battery inputs switched
195191 07/02/10 13:55 pking Work on the R2R3 master trigger so far
195189 07/02/10 12:48 mack removed the helicity signal from MD3+
195188 07/02/10 11:23 pking DAQ on cdaql6 is in use for R2R3 tests
195187 07/02/10 10:42 pking Plugged in DH ethernet cable 5 into small switch
195186 07/02/10 10:01 jmammei Compton: cleaning the hall
195185 07/02/10 09:26 pking Resuming DAQ tests for TrigScint on cdaql4
Thursday
195184 07/01/10 23:17 brads Gas flow to GEMs turned on sometime this morning
195183 07/01/10 21:10 pking Completed ROC4 DAQ tests; cdaql4 DAQ is free
195182 07/01/10 21:09 pking ROC4 tests from TrigScint
195181 07/01/10 20:32 pking Completed halo monitor DAQ tests; cdaql6 DAQ is free
195180 07/01/10 20:30 pking Halo monitor DAQ tests
195179 07/01/10 19:55 pking Beginning DAQ tests for halo monitors on cdaql6
195178 07/01/10 18:34 pking Beginning DAQ tests for ROC4 on cdaql4
195177 07/01/10 17:46 Nuruzzaman Beam Modulation Connections @ BSY
195176 07/01/10 16:28 rob md current mode test done, cdaql6 available for r2/r3 again
195175 07/01/10 16:16 rob main detector: trigger confusion, event mode okay
195174 07/01/10 15:51 mack MD work in octant 8
195173 07/01/10 15:51 Leckey cdaql6 Taking Data
195172 07/01/10 14:21 mack set ITRIP time constants in CAEN mainframes
195171 07/01/10 13:40 rob md configuration change: x=current mode, + = event mode
195170 07/01/10 13:30 rob main detector electronics on isolation transformer
195169 07/01/10 12:04 paschke replugged bpm0i01 cables to injector daq, removed qpd patch to injector daq
195168 07/01/10 10:27 paschke changed default greenmonster executable
195167 07/01/10 10:08 mack HV gui question