Difference between revisions of "How-to"
From HallCWiki
| Line 19: | Line 19: | ||
** [[Hall-C_HMS_DAQ_Failure_Modes | "HMS DC may be ringing (check replay now)" alarm]] | ** [[Hall-C_HMS_DAQ_Failure_Modes | "HMS DC may be ringing (check replay now)" alarm]] | ||
| − | * [https://hallcweb.jlab.org/DocDB/0010/001002/ | + | * [https://hallcweb.jlab.org/DocDB/0010/001002/002/Instructions-power-cycle-HallC-collimators.pdf Instructions for power cycling the drive controllers for the HMS/SHMS collimators]. |
** [https://hallcweb.jlab.org/DocDB/0008/000828/001/hallc_collimators.pdf More detailed info on collimator controls]. Also includes description of the collimators. | ** [https://hallcweb.jlab.org/DocDB/0008/000828/001/hallc_collimators.pdf More detailed info on collimator controls]. Also includes description of the collimators. | ||
** EPICS screens can be found at jmenu -> <search for> "HMS coll" and you'll see both entries | ** EPICS screens can be found at jmenu -> <search for> "HMS coll" and you'll see both entries | ||
Revision as of 11:44, 19 January 2019
NOTE: If you can't solve the problem in 1 hour you MUST then contact the Run Coordinator! (See also Experts on call)
Contents
How-to's
- The Hall C Operations Manual is a thorough and up-to-date set of instructions.
- Make HCLog entries using the logbook page, or by running 'hclog' in a terminal.
- Please be concise, but clear. Assume you will need to search for, and understand, an entry 12 months from now (or longer).
- Electronic Shift Checklist should be completed once per shift.
- This 'How to' page can help you find most items (see below). You may also find the instructions here helpful.
- DAQ Related Help
- Instructions for power cycling the drive controllers for the HMS/SHMS collimators.
- More detailed info on collimator controls. Also includes description of the collimators.
- EPICS screens can be found at jmenu -> <search for> "HMS coll" and you'll see both entries
- The usual collimator settings are HMS : "Large Collimator" and SHMS : "Collimator".
- Hall C Scalers & xscalers instructions for HMS and SHMS.
- Gas Shed
- Drift Chamber Gas System
- See Standard Equipment Manual
- Flow and Temperature Charts (generated by iochcgs.acc.jlab.org)
- Cerenkov Gas System
- Drift Chamber Gas System
- High Voltage Controls
- Run 'go_hv' and follow instructions
- EPICS/Accelerator Screens
- Also includes Stripcharts, Gas System info, Collimator controls, Chamber Thresholds, Harps, etc...
- Hall C BPMs: Run go_bpms from the cdaq account
- How to see results of Hall C harp scans
- How to bring up the Hall C YAG Viewer camera
- How to bring up the Alarm Handler
- Hall C cameras
- Hall C BCM Temperatures
- How to restore the Hall C EDTM Pulser
- How to check the HMS/SHMS shutters
- How to perform pedestal runs and determine FADC thresholds
- How to perform raster runs (this is the equivalent of spot++)
- How to check the HMS discriminator threshold read back
- How to perform a BCM calibration
Spectrometer Magnets
- Magnet screen is brought up on any hcdesk machine by the command go_magnets
- Note: only ONE copy of the magnet control GUI screen can be running. Creating a new one will cause the old one to disappear.
- How to operate and monitor the Spectrometer Magnets
- Spectrometer Magnets Cryogenics
- Resetting Magnet Interlocks
- How-to power cycle SHMS PLC I/O chassis: https://logbooks.jlab.org/entry/3625900
How to Rotate the HMS and SHMS
SHMS Detectors
HMS Detectors
Hall C target
Hall C target configuration for Spring 17 running
