Difference between revisions of "How-to"
From HallCWiki
(→General How-to's) |
(→Polarized He3 Target Information) |
||
| Line 2: | Line 2: | ||
== Polarized He3 Target Information == | == Polarized He3 Target Information == | ||
| + | [[Image:polhe3_target_screen_layout.png|thumb|Suggested Screen Layout]] | ||
[[Pol_He-3_Target_Information|Polarized He3 Target Information]] | [[Pol_He-3_Target_Information|Polarized He3 Target Information]] | ||
| + | |||
| + | To setup non-LabVIEW screens (stripcharts, target ladder, etc) | ||
| + | open a terminal on a clear workspace on HCDESK4 and run '''go_target''' | ||
== General How-to's == | == General How-to's == | ||
Revision as of 04:32, 8 December 2019
NOTE: If you can't solve the problem in 1 hour you MUST then contact the Run Coordinator! (See also Experts on call)
Contents
Polarized He3 Target Information
Polarized He3 Target Information
To setup non-LabVIEW screens (stripcharts, target ladder, etc) open a terminal on a clear workspace on HCDESK4 and run go_target
General How-to's
- The Hall C Operations Manual is a thorough and up-to-date set of instructions.
- Make HCLog entries using the logbook page, or by running 'hclog' in a terminal.
- Please be concise, but clear. Assume you will need to search for, and understand, an entry 12 months from now (or longer).
- Electronic Shift Checklist should be completed once per shift.
- DAQ Related Help
- Instructions for power cycling the drive controllers for the HMS/SHMS collimators.
- More detailed info on collimator controls. Also includes description of the collimators.
- EPICS screens can be found at jmenu -> <search for> "HMS coll" and you'll see both entries
- The usual collimator settings are HMS : "Large Collimator" and SHMS : "Collimator".
- Hall C Scalers & xscalers instructions for HMS and SHMS.
- Gas Shed
- Drift Chamber Gas System
- See Standard Equipment Manual
- Flow and Temperature Charts (generated by iochcgs.acc.jlab.org)
- Drift Chamber Gas System
- High Voltage Controls
- Run 'go_hv' and follow instructions
- EPICS/Accelerator Screens
- Also includes Stripcharts, Gas System info, Collimator controls, Chamber Thresholds, Harps, Energy/Position Locks, etc...
- Hall C Drift Chamber Threshold Controls
- Hall C BPMs: Run go_bpms from the cdaq account
- How to see results of Hall C harp scans
- How to bring up the Hall C YAG Viewer camera
- How to bring up the Alarm Handler
- Hall C cameras
- Hall C BCM Temperatures
- How to restore the Hall C EDTM Pulser
- How to check the HMS/SHMS shutters
- How to perform pedestal runs and determine FADC thresholds
- How to perform raster runs (this is the equivalent of spot++)
- Bull's Eye Scan -- BPM calibration instructions
- How to check the HMS discriminator threshold read back
- How to perform a BCM calibration
- How to operate the Hall-C Radiator (J/Psi Experiment)
Spectrometer Magnets
- Magnet screen is brought up on any hcdesk machine by the command go_magnets
- Note: only ONE copy of the magnet control GUI screen can be running. Creating a new one will cause the old one to disappear.
- How to operate and monitor the Spectrometer Magnets
- Spectrometer Magnets Cryogenics
- Resetting Magnet Interlocks
- How-to power cycle SHMS PLC I/O chassis: https://logbooks.jlab.org/entry/3625900
How to Rotate the HMS and SHMS
SHMS Detectors
HMS Detectors
Polarized 3He target in Hall C
Hall C Cryo-target
- Hall C 12-GeV Era Cryotarget Instructions
- Hall C target configuration for Spring 17 running
- How to operate the Hall-C Bremsstrahlung Radiator for the J/Ψ -007 Experiment (Spring 2019)
