Difference between revisions of "How-to"
From HallCWiki
(→General How-to's) |
(→General How-to's) |
||
| Line 64: | Line 64: | ||
*[[Hall C Raster Runs | How to perform raster runs]] (this is the equivalent of spot++) | *[[Hall C Raster Runs | How to perform raster runs]] (this is the equivalent of spot++) | ||
*[[Bull's Eye Scan | Bull's Eye Scan -- BPM calibration instructions]] | *[[Bull's Eye Scan | Bull's Eye Scan -- BPM calibration instructions]] | ||
| − | *[https://logbooks.jlab.org/entry/3588049 How to check the HMS discriminator threshold read back] | + | * HMS discriminator threshold read back is now in the Alarm Handler (no manual check required) |
| + | ** [https://logbooks.jlab.org/entry/3588049 How to check the HMS discriminator threshold read back] -- Obsolete | ||
| + | ** [https://logbooks.jlab.org/entry/3811562 HMS discriminator threshold added to alarm handler] -- Updated entry (June, 2020) | ||
* [https://hallcweb.jlab.org/DocDB/0009/000957/001/NonInvasiveBCMCalibration.pdf How to perform a BCM calibration] | * [https://hallcweb.jlab.org/DocDB/0009/000957/001/NonInvasiveBCMCalibration.pdf How to perform a BCM calibration] | ||
* [https://hallcweb.jlab.org/DocDB/0010/001006/001/Radiator.pdf How to operate the Hall-C Radiator (J/Psi Experiment)] | * [https://hallcweb.jlab.org/DocDB/0010/001006/001/Radiator.pdf How to operate the Hall-C Radiator (J/Psi Experiment)] | ||
Revision as of 15:34, 11 June 2020
NOTE: If you can't solve the problem in 1 hour you MUST then contact the Run Coordinator! (See also Experts on call)
Contents
Polarized He3 Target Information
Pol He-3 Target Screen Setup / How-tos
Polarized He3 Target Information
Pol He3 Operational Restrictions (raster, beam current limits, etc)
General How-to's
- The Hall C Operations Manual is a thorough and up-to-date set of instructions.
- Make HCLog entries using the logbook page, or by running 'hclog' in a terminal.
- Please be concise, but clear. Assume you will need to search for, and understand, an entry 12 months from now (or longer).
- Electronic Shift Checklist should be completed once per shift.
- Hall C Raster
- If problems call Raster experts in order of listed on Expert on call page.
- Raster procedure is located at Hall C Fast Raster Setup Procedure
- The raster X and Y signals that go into the DAQ are also shown on an oscilliscope in rack CH03B14. See logbook entry for a movie of good oscilliscope signals. The X and Y should be 90 degrees out of phase and the amplitude variation in sync.
- If raster signal's amplitude variation is not in sync, then ask MMC to go to the "Waveform Generator" page ( top right corner of the Hall C fast raster page). On the "Waveform Generator" page have MCC click on the "SYNC ARB" button.
- If raster signal's phase is not 90 degrees, then ask MMC to go to the "Waveform Generator" page ( top right corner of the Hall C fast raster page). On the "Waveform Generator" page have MCC click on the "SYNC PHASE" button.
- DAQ Related Help
- Collimator, Sieve Controls
- EPICS screens can be found at jmenu -> <search for> "HMS coll" and you'll see both entries
- The usual collimator settings are HMS : "Large Collimator" and SHMS : "Collimator".
- The usual sieve settings are "HMS: Sieve" and SHMS: "Centered Sieve"
- Instructions for power cycling the drive controllers for the HMS/SHMS collimators.
- More detailed info on collimator controls. Also includes description of the collimators.
- EPICS screens can be found at jmenu -> <search for> "HMS coll" and you'll see both entries
- Hall C Scalers & xscalers instructions for HMS and SHMS.
- Gas Shed
- Drift Chamber Gas System
- See Standard Equipment Manual
- Flow and Temperature Charts (generated by iochcgs.acc.jlab.org)
- Drift Chamber Gas System
- High Voltage Controls
- Run 'go_hv' and follow instructions
- EPICS/Accelerator Screens
- Also includes Stripcharts, Gas System info, Collimator controls, Chamber Thresholds, Harps, Energy/Position Locks, etc...
- Hall C Drift Chamber Threshold Controls
- Hall C BPMs: Run go_bpms from the cdaq account
- How to see results of Hall C harp scans
- How to bring up the Hall C YAG Viewer camera
- How to bring up the Alarm Handler
- Hall C cameras
- Hall C BCM Temperatures
- How to restore the Hall C EDTM Pulser
- How to check the HMS/SHMS shutters
- How to perform pedestal runs and determine FADC thresholds
- How to perform raster runs (this is the equivalent of spot++)
- Bull's Eye Scan -- BPM calibration instructions
- HMS discriminator threshold read back is now in the Alarm Handler (no manual check required)
- How to check the HMS discriminator threshold read back -- Obsolete
- HMS discriminator threshold added to alarm handler -- Updated entry (June, 2020)
- How to perform a BCM calibration
- How to operate the Hall-C Radiator (J/Psi Experiment)
- How to check if the beam current ramp protection is on (Pol He3)
- How to open target BPM screen
Spectrometer Magnets
- Magnet screen is brought up on any hcdesk machine by the command go_magnets
- Note: only ONE copy of the magnet control GUI screen can be running. Creating a new one will cause the old one to disappear.
- How to operate and monitor the Spectrometer Magnets
- Spectrometer Magnets Cryogenics
- Resetting Magnet Interlocks
- How-to power cycle SHMS PLC I/O chassis: https://logbooks.jlab.org/entry/3625900
How to Rotate the HMS and SHMS
SHMS Detectors
HMS Detectors
Polarized 3He target in Hall C
Hall C Cryo-target
- Hall C 12-GeV Era Cryotarget Instructions
- Hall C target configuration for Spring 17 running
- How to operate the Hall-C Bremsstrahlung Radiator for the J/Ψ -007 Experiment (Spring 2019)
